EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Characteristics of Epoxy Composites Containing Carbon Nanotubes/Graphene Mixtures

Tatiana P Dyachkova iD, Yulian A Khan, Elena A Burakova, Evgeny V Galunin iD, Gulnara N Shigabaeva, Dmitry N Stolbov iD, Georgy A Titov, Nikolay A Chapaksov, Alexey G Tkachev

Polymers · 16.03.2023 · 15 (6) · 1476

DOI: 10.3390/polym15061476 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 16.03.2023. Verfasst von Tatiana P Dyachkova und 8 weiteren Autor:innen. Beteiligte Einrichtung: Research Department «Technology and Methods of Nanoproducts Manufacturing», Technological Institute, Tambov State Technical University, 106/5, Buildi…. Die Arbeit wurde bisher 46-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The paper considers the development of fillers representing mixtures of carbon nanotubes and graphene materials (graphene oxide and graphene nanoplatelets) in different mass ratios to modify epoxy resin. The graphene type and content effect on the dispersed phase particle effective sizes—both in aqueous suspensions and the resin—was analyzed. Hybrid particles were characterized by Raman spectroscopy and electron microscopy. The composites containing 0.15–1.00 wt.% CNTs/GO and CNTs/GNPs were thermogravimetrically analyzed, and their mechanical characteristics were determined. SEM images of the composite fracture surfaces were acquired. Optimal dispersions containing 75–100 nm particles were obtained at the CNTs:GO mass ratio of 1:4. It was shown that the CNTs can be located between the GO layers and on the GNP surface. The samples containing up to 0.2 wt.% CNTs/GO (at 1:1 and 1:4 ratios) were stable when heated in air up to 300 °C. For 0.15–0.20 wt.% CNTs/GO (at 1:1 ratio), the tensile strength and modulus of the composite increased by 84–88 and 40%, respectively. The increase in the strength characteristics was found to occur due to the interaction of the filler layered structure with the polymer matrix. The obtained composites can be used as structural materials in different fields of engineering.

Schlagwörter

Stichwörter der Autor:innen

carbon nanotubesepoxy compositesgraphene nanoplatesgraphene oxidemechanical properties

Autor:innen und Institutionen

  • Research Department «Technology and Methods of Nanoproducts Manufacturing», Technological Institute, Tambov State Technical University, 106/5, Building 2, Sovetskaya St., 392000 Tambov, Russia.
  • Department of Organic and Ecological Chemistry, Institute of Chemistry, University of Tyumen, 6 Volodarskogo St., 625003 Tyumen, Russia.
  • Laboratory of Catalysis and Gas Electrochemistry, Faculty of Chemistry, Lomonosov Moscow State University, 1 Leninskiye Gory, 119991 Moscow, Russia.

ORCID-Profile: Tatiana P Dyachkova, Evgeny V Galunin, Dmitry N Stolbov

Förderung

  • Russian Science Foundation

Zitieren

APA

Dyachkova, T. P., Khan, Y. A., Burakova, E. A., Galunin, E. V., Shigabaeva, G. N., Stolbov, D. N., Titov, G. A., Chapaksov, N. A., & Tkachev, A. G. (2023). Characteristics of Epoxy Composites Containing Carbon Nanotubes/Graphene Mixtures. Polymers, 15(6), 1476. https://doi.org/10.3390/polym15061476

Vancouver

Dyachkova TP, Khan YA, Burakova EA, Galunin EV, Shigabaeva GN, Stolbov DN, et al. Characteristics of Epoxy Composites Containing Carbon Nanotubes/Graphene Mixtures. Polymers. 2023;15(6):1476. doi:10.3390/polym15061476

BibTeX
@article{Dyachkova2023,
  author = {Dyachkova, Tatiana P and Khan, Yulian A and Burakova, Elena A and Galunin, Evgeny V and Shigabaeva, Gulnara N and Stolbov, Dmitry N and Titov, Georgy A and Chapaksov, Nikolay A and Tkachev, Alexey G},
  title = {Characteristics of Epoxy Composites Containing Carbon Nanotubes/Graphene Mixtures},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {6},
  pages = {1476},
  doi = {10.3390/polym15061476}
}
Kostenlos starten →