Modelling of Nonthermal Dielectric Barrier Discharge Plasma at Atmospheric Pressure and Role of Produced Reactive Species in Surface Polymer Microbial Purification
Polymers · 28.02.2023 · 15 (5) · 1235
DOI: 10.3390/polym15051235 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 28.02.2023. Verfasst von Samira Elaissi und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Physics, College of Science, Princess Nourah Bint Abdulrahman University, P.O. Box 84428, Riyadh 11671, Saudi Arabia. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 70 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deputyship for Research & Innovation, Ministry of Education in Saudi Arabia, Deputyship for Research & Innovation, Ministry of Education in Saudi Arabia.
Abstract (Originalsprache)
A nonthermal atmospheric plasma reactor was used to sterilize polymer surfaces and satisfy safety constraints in a biological medium. A 1D fluid model was developed using COMSOL Multiphysics software® 5.4 with a helium–oxygen mixture at low temperature for the decontamination of bacteria on polymer surfaces. An analysis of the evolution of the homogeneous dielectric barrier discharge (DBD) was carried out through studying the dynamic behavior of the discharge parameters including the discharge current, the consumed power, the gas gap voltage, and transport charges. In addition, the electrical characteristics of a homogeneous DBD under different operating conditions were studied. The results shown that increasing voltage or frequency caused higher ionization levels and maximum increase of metastable species’ density and expanded the sterilization area. On the other hand, it was possible to operate plasma discharges at a low voltage and a high density of plasma using higher values of the secondary emission coefficient or permittivity of the dielectric barrier materials. When the discharge gas pressure increased, the current discharges declined, which indicated a lower sterilization efficiency under high pressure. A short gap width and the admixture of oxygen were needed for sufficient bio-decontamination. Plasma-based pollutant degradation devices could therefore benefit from these results.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Physics, College of Science, Princess Nourah Bint Abdulrahman University, P.O. Box 84428, Riyadh 11671, Saudi Arabia.
ORCID-Profile: Samira Elaissi
Förderung
- Deputyship for Research & Innovation, Ministry of Education in Saudi Arabia
- Deputyship for Research & Innovation, Ministry of Education in Saudi Arabia
Zitieren
APA
Elaissi, S., & Alsaif, N. A. M. (2023). Modelling of Nonthermal Dielectric Barrier Discharge Plasma at Atmospheric Pressure and Role of Produced Reactive Species in Surface Polymer Microbial Purification. Polymers, 15(5), 1235. https://doi.org/10.3390/polym15051235
Vancouver
Elaissi S, Alsaif NAM. Modelling of Nonthermal Dielectric Barrier Discharge Plasma at Atmospheric Pressure and Role of Produced Reactive Species in Surface Polymer Microbial Purification. Polymers. 2023;15(5):1235. doi:10.3390/polym15051235
BibTeX
@article{Elaissi2023,
author = {Elaissi, Samira and Alsaif, Norah A M},
title = {Modelling of Nonthermal Dielectric Barrier Discharge Plasma at Atmospheric Pressure and Role of Produced Reactive Species in Surface Polymer Microbial Purification},
journal = {Polymers},
year = {2023},
volume = {15},
number = {5},
pages = {1235},
doi = {10.3390/polym15051235}
}
EUVIMED