EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D Printed Functionalized Nanocellulose as an Adsorbent in Batch and Fixed-Bed Systems

Mohd Shaiful Sajab iD, Wan Nazihah Liyana Wan Jusoh, Denesh Mohan iD, Hatika Kaco, Rubiyah Baini

Polymers · 15.02.2023 · 15 (4) · 969

DOI: 10.3390/polym15040969 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 15.02.2023. Verfasst von Mohd Shaiful Sajab und 4 weiteren Autor:innen. Beteiligte Einrichtung: Research Center for Sustainable Process Technology (CESPRO), Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 4360…. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Higher Education.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Nanocellulose, a refined form of cellulose, can be further functionalized on surface-active sites, with a catalyst as a regenerative agent. Newly developed adsorbents are expected to have the characteristics of good and rapid adsorption performance and regeneration properties with flexible structure using 3D printing technology. In this work, the adsorption performance of 3D printed functionalized nanocellulose was investigated using batch and fixed-bed column adsorption. Kinetics adsorption studies were divided into different adsorption models, with the pseudo-second order model showing a better correlation coefficient than the pseudo-first order and intraparticle diffusion models. The Langmuir and Thomas models were used to calculate the adsorption performance of batch and fixed-bed columns. Given the catalytic activity of Fenton oxidation, the fixed-bed column was regenerated up to five adsorption-desorption cycles, suggesting satisfactory performance of the column, with a slightly reduced adsorption capacity.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingcellulosewater remediation

Autor:innen und Institutionen

  • Research Center for Sustainable Process Technology (CESPRO), Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia.
  • Department of Chemical and Process Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia.
  • Kolej GENIUS Insan, Universiti Sains Islam Malaysia, Bandar Baru Nilai, Nilai 71800, Negeri Sembilan, Malaysia.
  • Faculty of Engineering, Universiti Malaysia Sarawak (UNIMAS), Kota Samarahan 94300, Sarawak, Malaysia.

ORCID-Profile: Mohd Shaiful Sajab, Denesh Mohan

Förderung

  • Ministry of Higher Education

Zitieren

APA

Sajab, M. S., Wan Jusoh, W. N. L., Mohan, D., Kaco, H., & Baini, R. (2023). 3D Printed Functionalized Nanocellulose as an Adsorbent in Batch and Fixed-Bed Systems. Polymers, 15(4), 969. https://doi.org/10.3390/polym15040969

Vancouver

Sajab MS, Wan Jusoh WNL, Mohan D, Kaco H, Baini R. 3D Printed Functionalized Nanocellulose as an Adsorbent in Batch and Fixed-Bed Systems. Polymers. 2023;15(4):969. doi:10.3390/polym15040969

BibTeX
@article{Sajab2023,
  author = {Sajab, Mohd Shaiful and Wan Jusoh, Wan Nazihah Liyana and Mohan, Denesh and Kaco, Hatika and Baini, Rubiyah},
  title = {3D Printed Functionalized Nanocellulose as an Adsorbent in Batch and Fixed-Bed Systems},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {4},
  pages = {969},
  doi = {10.3390/polym15040969}
}
Kostenlos starten →