EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Flexural Performance and End Debonding Prediction of NSM Carbon FRP-Strengthened Reinforced Concrete Beams under Different Service Temperatures

Marta Baena iD, Younes Jahani iD, Lluís Torres iD, Cristina Barris iD, Ricardo Perera iD

Polymers · 08.02.2023 · 15 (4) · 851

DOI: 10.3390/polym15040851 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 08.02.2023. Verfasst von Marta Baena und 4 weiteren Autor:innen. Beteiligte Einrichtung: Analysis and Advanced Materials for Structural Design (AMADE), Polytechnic School, University of Girona, 17003 Girona, Spain. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Spanish Ministry of Science and Innovation (MCIN), Government of Catalonia, Generalitat de Catalunya.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper aims to evaluate the influence of relatively high service temperatures (near or beyond the glass transition temperature (Tg) of epoxy adhesive) on the flexural performance and end debonding phenomenon in near-surface mounted (NSM) carbon fiber-reinforced polymer (CFRP)-strengthened, reinforced concrete (RC) beams. To this end, an experimental program consisting of 24 beams (divided into four groups) was performed, where different parameters was combined (i.e., service temperature, steel reinforcement ratio, CFRP ratio, and concrete compressive strength). In addition, the effect of the testing temperature on the end debonding phenomenon was investigated with an analytical procedure according to fib Bulletin 90, and the predictions were compared to experimental results. Taking specimens tested at 20 °C as a reference, no considerable change was observed in the ultimate load of the specimens tested below 60 °C (being in the range of epoxy Tg), and all specimens failed by FRP rupture. On the other hand, the increase in testing temperature up to 70 and 85 °C was followed by a decrease in the capacity of the strengthened beams and a change in failure mode, moving from FRP rupture to end debonding and concrete crushing. The analytical procedure successfully predicted the occurrence of premature end debonding failure and demonstrated that the effect of temperature on the mechanical properties of materials can be a key factor when predicting the premature end debonding in a NSM joint.

Schlagwörter

Stichwörter der Autor:innen

NSM CFRP-strengtheningend debondingexperimentalservice temperature

Autor:innen und Institutionen

  • Analysis and Advanced Materials for Structural Design (AMADE), Polytechnic School, University of Girona, 17003 Girona, Spain.
  • Department of Mechanical Engineering, Technical University of Madrid, 28006 Madrid, Spain.

ORCID-Profile: Marta Baena, Younes Jahani, Lluís Torres, Cristina Barris, Ricardo Perera

Förderung

  • Spanish Ministry of Science and Innovation (MCIN)
  • Government of Catalonia
  • Generalitat de Catalunya

Zitieren

APA

Baena, M., Jahani, Y., Torres, L., Barris, C., & Perera, R. (2023). Flexural Performance and End Debonding Prediction of NSM Carbon FRP-Strengthened Reinforced Concrete Beams under Different Service Temperatures. Polymers, 15(4), 851. https://doi.org/10.3390/polym15040851

Vancouver

Baena M, Jahani Y, Torres L, Barris C, Perera R. Flexural Performance and End Debonding Prediction of NSM Carbon FRP-Strengthened Reinforced Concrete Beams under Different Service Temperatures. Polymers. 2023;15(4):851. doi:10.3390/polym15040851

BibTeX
@article{Baena2023,
  author = {Baena, Marta and Jahani, Younes and Torres, Lluís and Barris, Cristina and Perera, Ricardo},
  title = {Flexural Performance and End Debonding Prediction of NSM Carbon FRP-Strengthened Reinforced Concrete Beams under Different Service Temperatures},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {4},
  pages = {851},
  doi = {10.3390/polym15040851}
}
Kostenlos starten →