EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Energy Absorption Behavior of 3D-Printed Polymeric Octet-Truss Lattice Structures of Varying Strut Length and Radius

Matthew Bolan, Mackenzie Dean, Alexander Bardelcik iD

Polymers · 31.01.2023 · 15 (3) · 713

DOI: 10.3390/polym15030713 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 31.01.2023. Verfasst von Matthew Bolan und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Engineering, College of Engineering and Physical Sciences, University of Guelph, Guelph, ON N1G 2W1, Canada. Die Arbeit wurde bisher 43-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Sciences and Engineering Research Council, Natural Sciences and Engineering Research Council of Canada (NSERC).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

We investigate the compressive energy absorption performance of polymeric octet-truss lattice structures that are 3D printed using high-resolution stereolithography. These structures are potential candidates for personal protective equipment, structural, and automotive applications. Two polymeric resins (high-strength/low-ductility and moderate-strength/high-ductility) were used in this work, and a comprehensive uniaxial tensile characterization was conducted to establish an optimal UV curing time. The external octet-truss structure geometry (3″ × 3″ × 3″) was maintained, and four different lattice cell densities (strut length, L) and three different strut radii (R) were printed, UV cured, and compression tested. The compressive stress–strain and energy absorption (EA) behavior were quantified, and the EA at 0.5 strain for the least dense and smallest R structure was 0.02 MJ/m3, while the highest density structure with the largest R was 1.80 MJ/m3 for Resin 2. The structural failure modes varied drastically based on resin type, and it was shown that EA and deformation behavior were related to L, R, and the structures’ relative density (ρ¯). For the ductile resin, an empirical model was developed to predict the EA vs. compressive strain curves based on L and R. This model can be used to design an octet-truss lattice structure based on the EA requirements of an application.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingempirical modelenergy absorptionfailure modesoctet-truss unit cellstereolithography (SLA) 3D printing

Autor:innen und Institutionen

  • School of Engineering, College of Engineering and Physical Sciences, University of Guelph, Guelph, ON N1G 2W1, Canada.

ORCID-Profile: Alexander Bardelcik

Förderung

  • Natural Sciences and Engineering Research Council
  • Natural Sciences and Engineering Research Council of Canada (NSERC)

Zitieren

APA

Bolan, M., Dean, M., & Bardelcik, A. (2023). The Energy Absorption Behavior of 3D-Printed Polymeric Octet-Truss Lattice Structures of Varying Strut Length and Radius. Polymers, 15(3), 713. https://doi.org/10.3390/polym15030713

Vancouver

Bolan M, Dean M, Bardelcik A. The Energy Absorption Behavior of 3D-Printed Polymeric Octet-Truss Lattice Structures of Varying Strut Length and Radius. Polymers. 2023;15(3):713. doi:10.3390/polym15030713

BibTeX
@article{Bolan2023,
  author = {Bolan, Matthew and Dean, Mackenzie and Bardelcik, Alexander},
  title = {The Energy Absorption Behavior of 3D-Printed Polymeric Octet-Truss Lattice Structures of Varying Strut Length and Radius},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {3},
  pages = {713},
  doi = {10.3390/polym15030713}
}
Kostenlos starten →