EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

In Vitro Mechanical Properties of a Novel Graphene-Reinforced PMMA-Based Dental Restorative Material

Francesco De Angelis iD, Mirco Vadini, Matteo Buonvivere, Antonio Valerio, Michele Di Cosola, Adriano Piattelli, Virginia Biferi, Camillo D'Arcangelo

Polymers · 25.01.2023 · 15 (3) · 622

DOI: 10.3390/polym15030622 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 25.01.2023. Verfasst von Francesco De Angelis und 7 weiteren Autor:innen. Beteiligte Einrichtung: Unit of Restorative Dentistry and Endodontics, Department of Medical, Oral and Biotechnological Sciences, University of Chieti, 66100 Chieti, Italy. Die Arbeit wurde bisher 32-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Recent studies suggest that the incorporation of graphene in resin-based dental materials might enhance their mechanical properties and even decrease their degree of contraction during polymerization. The present study aimed at comparing the three-point flexural strength (FS), the compressive strength (CS), and the Vickers hardness (VH) of a CAD/CAM poly-methylmethacrylate (PMMA)-based resin, a recently introduced graphene-reinforced CAD/CAM PMMA-based resin (G-PMMA), and a conventional dental bis-acryl composite resin (BACR). No significant differences (p > 0.05) were detected among the materials in terms of flexural strength. On the other hand, a mean flexural modulus value of 9920.1 MPa was recorded in BACR group, significantly higher compared to the flexural modulus detected for G-PMMA (2670.2 MPa) and for conventional PMMA (2505.3) (p < 0.05). In terms of compressive modulus (MPa) and compressive strength (MPa), BACR was significantly stiffer than PMMA and G-PMMA. Concerning VH measurements, a significantly increased hardness emerged comparing the BACR group (VH 98.19) to both PMMA and G-PMMA groups (VH 34.16 and 34.26, respectively). Based on the finding of the present study, the graphene-reinforced (PMMA)-based polymer herein tested was not superior to the conventional PMMA and seemed not able to be considered as an alternative material for permanent restorations, at least in terms of hardness and mechanical response to compressive stress. More research on the mechanical/biological properties of G-PMMAs (and on graphene as a filler) seems still necessary to better clarify their potential as dental restorative materials.

Schlagwörter

Stichwörter der Autor:innen

PMMAVickers hardnesscompressive strengthflexural strengthgrapheneresin-based composites

Autor:innen und Institutionen

  • Unit of Restorative Dentistry and Endodontics, Department of Medical, Oral and Biotechnological Sciences, University of Chieti, 66100 Chieti, Italy.
  • Department of Clinical and Experimental Medicine, University of Foggia, 71122 Foggia, Italy.
  • School of Dentistry, Saint Camillus International University of Health and Medical Sciences, Via di Sant'Alessandro 8, 00131 Rome, Italy.

ORCID-Profile: Francesco De Angelis

Zitieren

APA

De Angelis, F., Vadini, M., Buonvivere, M., Valerio, A., Di Cosola, M., Piattelli, A., Biferi, V., & D'Arcangelo, C. (2023). In Vitro Mechanical Properties of a Novel Graphene-Reinforced PMMA-Based Dental Restorative Material. Polymers, 15(3), 622. https://doi.org/10.3390/polym15030622

Vancouver

De Angelis F, Vadini M, Buonvivere M, Valerio A, Di Cosola M, Piattelli A, et al. In Vitro Mechanical Properties of a Novel Graphene-Reinforced PMMA-Based Dental Restorative Material. Polymers. 2023;15(3):622. doi:10.3390/polym15030622

BibTeX
@article{DeAngelis2023,
  author = {De Angelis, Francesco and Vadini, Mirco and Buonvivere, Matteo and Valerio, Antonio and Di Cosola, Michele and Piattelli, Adriano and Biferi, Virginia and D'Arcangelo, Camillo},
  title = {In Vitro Mechanical Properties of a Novel Graphene-Reinforced PMMA-Based Dental Restorative Material},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {3},
  pages = {622},
  doi = {10.3390/polym15030622}
}
Kostenlos starten →