Multi-Material Additive Manufacturing of High Temperature Polyetherimide (PEI)–Based Polymer Systems for Lightweight Aerospace Applications
Polymers · 21.01.2023 · 15 (3) · 561
DOI: 10.3390/polym15030561 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 21.01.2023. Verfasst von Ved S Vakharia und 3 weiteren Autor:innen. Beteiligte Einrichtung: NASA Pathway Intern, Department of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA 92092, USA. Die Arbeit wurde bisher 54-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Lewis’ Educational and Research Collaborative Internship Project (LERCIP), NASA Pathways Program, Revolutionary Vertical Lift Technology (RVLT) Project.
Abstract (Originalsprache)
Rapid innovations in 3-D printing technology have created a demand for multifunctional composites. Advanced polymers like amorphous thermoplastic polyetherimide (PEI) can create robust, lightweight, and efficient structures while providing high-temperature stability. This work manufactured ULTEM, a PEI-based polymer, and carbon-fiber-infused ULTEM multi-material composites with varying layering patterns (e.g., AAABBB vs. ABABAB) using fused filament fabrication (FFF). The microstructure of fractured surfaces and polished cross-sections determined that the print quality of layers printed closer to the heated bed was higher than layers closer to the top surface, primarily due to the thermal insulating properties of the material itself. Mechanical properties of the multi-material parts were between those of the single-material parts: an ultimate tensile strength and elastic modulus of 59 MPa and 3.005 GPa, respectively. Multi-material parts from the same filaments but with different layering patterns showed different mechanical responses. Prints were of higher quality and demonstrated a higher elastic modulus (3.080 GPa) when consecutive layers were printed from the same filament (AAABBB) versus parts with printed layers of alternating filaments (ABABAB), which showed a higher ultimate strength (62.04 MPa). These results demonstrate the potential for creatively designing multi-material printed parts that may enhance mechanical properties.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- NASA Pathway Intern, Department of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA 92092, USA.
- Beta Technologies, Burlington, VT 05403, USA.
- Ohio Aerospace Institute, Cleveland, OH 44142, USA.
- NASA Glenn Research Center, Cleveland, OH 44135, USA.
ORCID-Profile: Ved S Vakharia
Förderung
- Lewis’ Educational and Research Collaborative Internship Project (LERCIP)
- NASA Pathways Program
- Revolutionary Vertical Lift Technology (RVLT) Project
Zitieren
APA
Vakharia, V. S., Leonard, H., Singh, M., & Halbig, M. C. (2023). Multi-Material Additive Manufacturing of High Temperature Polyetherimide (PEI)–Based Polymer Systems for Lightweight Aerospace Applications. Polymers, 15(3), 561. https://doi.org/10.3390/polym15030561
Vancouver
Vakharia VS, Leonard H, Singh M, Halbig MC. Multi-Material Additive Manufacturing of High Temperature Polyetherimide (PEI)–Based Polymer Systems for Lightweight Aerospace Applications. Polymers. 2023;15(3):561. doi:10.3390/polym15030561
BibTeX
@article{Vakharia2023,
author = {Vakharia, Ved S and Leonard, Hunter and Singh, Mrityunjay and Halbig, Michael C},
title = {Multi-Material Additive Manufacturing of High Temperature Polyetherimide (PEI)–Based Polymer Systems for Lightweight Aerospace Applications},
journal = {Polymers},
year = {2023},
volume = {15},
number = {3},
pages = {561},
doi = {10.3390/polym15030561}
}
EUVIMED