EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of 3D Printed Multi-Layered Orodispersible Films with Porous Structure Applicable as a Substrate for Inkjet Printing

Jan Elbl iD, Martin Veselý iD, Dagmar Blaháčková, Jaroslav Ondruš iD, Pavel Kulich, Eliška Mašková iD, Josef Mašek, Jan Gajdziok iD

Pharmaceutics · 20.02.2023 · 15 (2) · 714

DOI: 10.3390/pharmaceutics15020714 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Pharmaceutics, online erschienen am 20.02.2023. Verfasst von Jan Elbl und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Pharmaceutical Technology, Faculty of Pharmacy, Masaryk University Brno, Palackého tř. 1946/1, 612 42 Brno, Czech Republic. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Masaryk University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The direct tailoring of the size, composition, or number of layers belongs to the advantages of 3D printing employment in producing orodispersible films (ODFs) compared to the frequently utilized solvent casting method. This study aimed to produce porous ODFs as a substrate for medicated ink deposited by a 2D printer. The innovative semi-solid extrusion 3D printing method was employed to produce multilayered ODFs, where the bottom layer assures the mechanical properties. In contrast, the top layer provides a porous structure for ink entrapment. Hydroxypropyl methylcellulose and polyvinyl alcohol were utilized as film-forming polymers, glycerol as a plasticizer, and sodium starch glycolate as a disintegrant in the bottom matrix. Several porogen agents (Aeroperl® 300, Fujisil®, Syloid® 244 FP, Syloid® XDP 3050, Neusilin® S2, Neusilin® US2, and Neusilin® UFL2) acted as porosity enhancers in the two types of top layer. ODFs with satisfactory disintegration time were prepared. The correlation between the porogen content and the mechanical properties was proved. A porous ODF structure was detected in most samples and linked to the porogen content. SSE 3D printing represents a promising preparation method for the production of porous ODFs as substrates for subsequent drug deposition by 2D printing, avoiding the difficulties arising in casting or printing medicated ODFs directly.

Schlagwörter

Stichwörter der Autor:innen

3D printfast dissolving filmsindividualized therapyinkjet printoral filmsporous films

Autor:innen und Institutionen

  • Department of Pharmaceutical Technology, Faculty of Pharmacy, Masaryk University Brno, Palackého tř. 1946/1, 612 42 Brno, Czech Republic.
  • Department of Pharmacology and Toxicology, Veterinary Research Institute, Hudcova 70, 621 00 Brno, Czech Republic.

ORCID-Profile: Jan Elbl, Martin Veselý, Jaroslav Ondruš, Eliška Mašková, Jan Gajdziok

Förderung

  • Masaryk University

Zitieren

APA

Elbl, J., Veselý, M., Blaháčková, D., Ondruš, J., Kulich, P., Mašková, E., Mašek, J., & Gajdziok, J. (2023). Development of 3D Printed Multi-Layered Orodispersible Films with Porous Structure Applicable as a Substrate for Inkjet Printing. Pharmaceutics, 15(2), 714. https://doi.org/10.3390/pharmaceutics15020714

Vancouver

Elbl J, Veselý M, Blaháčková D, Ondruš J, Kulich P, Mašková E, et al. Development of 3D Printed Multi-Layered Orodispersible Films with Porous Structure Applicable as a Substrate for Inkjet Printing. Pharmaceutics. 2023;15(2):714. doi:10.3390/pharmaceutics15020714

BibTeX
@article{Elbl2023,
  author = {Elbl, Jan and Veselý, Martin and Blaháčková, Dagmar and Ondruš, Jaroslav and Kulich, Pavel and Mašková, Eliška and Mašek, Josef and Gajdziok, Jan},
  title = {Development of 3D Printed Multi-Layered Orodispersible Films with Porous Structure Applicable as a Substrate for Inkjet Printing},
  journal = {Pharmaceutics},
  year = {2023},
  volume = {15},
  number = {2},
  pages = {714},
  doi = {10.3390/pharmaceutics15020714}
}
Kostenlos starten →