Development and Evaluation of 3D-Printed Losartan Potassium Tablets Using Semi-Solid Extrusion: The Effect of Geometry, Drug Loading and Superdisintegrant
Pharmaceuticals · 07.10.2025 · 18 (10) · 1504
DOI: 10.3390/ph18101504 ↗Kurz gefasst
Fachartikel in der Zeitschrift Pharmaceuticals, online erschienen am 07.10.2025. Verfasst von Aleksandra Vojinović und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute for Medicines and Medical Devices of Montenegro, 81000 Podgorica, Montenegro. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science, Technological Development and Innovation, Republic of Serbia.
Abstract (Originalsprache)
Background/Objectives: Semi-solid extrusion (SSE) three-dimensional (3D) printing offers a versatile approach for fabricating personalized oral dosage forms. This study aimed to develop and optimize losartan potassium tablets produced via SSE 3D printing, focusing on the effects of polymer composition, tablet geometry, drug loading, and superdisintegrant concentration on printability and performance characteristics.
Methods
Formulations containing hydroxypropyl methylcellulose (HPMC) 4500 at various concentrations were evaluated for suitability in an ethanol–water (9:1 v/v) solvent system. The optimized formulation (5% w/w HPMC 4500) was used to print tablets with varying shapes, drug loadings (5–15% w/w; approximately 50–150 mg losartan potassium per tablet), and croscarmellose sodium concentrations (0–3% w/w). Printed tablets were characterized for dimensional accuracy, mass uniformity, disintegration time, and drug release behavior. Drug release kinetics were modeled to elucidate the release mechanism.
Results
All SSE-printed tablets exhibited excellent dimensional precision (SD < 0.8 mm) and mass uniformity (SD < 0.12 g). Increasing drug loading enhanced the initial release rate, reaching up to 63% in 45 min for 15% loading. The addition of 1% croscarmellose sodium reduced disintegration time to approximately 25 min. Drug release profiles were best described by the Korsmeyer–Peppas model (R2 > 0.96), indicating diffusion-controlled release.
Conclusions
SSE 3D printing demonstrated robustness and flexibility in producing losartan potassium tablets with consistent quality, tunable release properties, and strong potential for personalized pharmaceutical manufacturing.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Institute for Medicines and Medical Devices of Montenegro, 81000 Podgorica, Montenegro.
- Faculty of Pharmacy, University of Belgrade, 11000 Belgrade, Serbia.
- Medical Faculty, Military Medical Academy, 11000 Belgrade, Serbia.
ORCID-Profile: Gordana Stanojević, Ivana Adamov, Svetlana Ibrić
Förderung
- Ministry of Science, Technological Development and Innovation, Republic of Serbia
Zitieren
APA
Vojinović, A., Medarević, Đ., Stanojević, G., Mirković, D., Mugoša, S., Adamov, I., & Ibrić, S. (2025). Development and Evaluation of 3D-Printed Losartan Potassium Tablets Using Semi-Solid Extrusion: The Effect of Geometry, Drug Loading and Superdisintegrant. Pharmaceuticals, 18(10), 1504. https://doi.org/10.3390/ph18101504
Vancouver
Vojinović A, Medarević Đ, Stanojević G, Mirković D, Mugoša S, Adamov I, et al. Development and Evaluation of 3D-Printed Losartan Potassium Tablets Using Semi-Solid Extrusion: The Effect of Geometry, Drug Loading and Superdisintegrant. Pharmaceuticals. 2025;18(10):1504. doi:10.3390/ph18101504
BibTeX
@article{Vojinovi2025,
author = {Vojinović, Aleksandra and Medarević, Đorđe and Stanojević, Gordana and Mirković, Dušica and Mugoša, Snežana and Adamov, Ivana and Ibrić, Svetlana},
title = {Development and Evaluation of 3D-Printed Losartan Potassium Tablets Using Semi-Solid Extrusion: The Effect of Geometry, Drug Loading and Superdisintegrant},
journal = {Pharmaceuticals},
year = {2025},
volume = {18},
number = {10},
pages = {1504},
doi = {10.3390/ph18101504}
}
EUVIMED