EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Silicon Nitride Nanopowder Content in Polyamide 12 (PA12) in Extrusion-Based Additive Manufacturing

Markos Petousis iD, Apostolos Korlos iD, Nikolaos Michailidis iD, Vassilis M Papadakis iD, Apostolos Argyros iD, Nikolaos Mountakis iD, Maria Spyridaki iD, Athena Maniadi iD, Amalia Moutsopoulou, Nectarios Vidakis

Nanomaterials · 29.12.2025 · 16 (1) · 47

DOI: 10.3390/nano16010047 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Nanomaterials, online erschienen am 29.12.2025. Verfasst von Markos Petousis und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Hellenic Mediterranean University, 71410 Heraklion, Greece. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 132 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The use of polyamide-12 (PA12) thermoplastics in additive manufacturing (AM) is promising owing to their mechanical properties and printability. However, in load-bearing applications, improvements in mechanical strength and stiffness are sought after. Herein, the reinforcement efficiency of silicon nitride (Si3N4) nanoparticles in the PA12 matrix was explored. The filler loading varied between 2.0 wt. % and 10.0 wt. %. The nanocomposites were extruded into filament using melt compounding for subsequent material extrusion (MEX) 3D printing. PA12/Si3N4 nanocomposites were examined for their thermal, rheological, morphological, and structural characteristics. For mechanical characterization, flexural, tensile, microhardness, and Charpy impact data were obtained. For structural examination, porosity and dimensional deviation were assessed. Scanning electron microscopy (SEM) was used to investigate morphology and chemical composition. The results indicate that Si3N4 nanopowder significantly improved all mechanical properties, with a greater than 20% increase in tensile strength and elastic modulus when compared to neat PA12. The structural characteristics were also improved. These findings indicate that Si3N4 nanoparticles provide a viable reinforcement filler for PA12 for use in lightweight, robust structural components fabricated using MEX AM. Furthermore, it can be stated that ceramic–polymer nanocomposites further improve the applicability of PA12, where high mechanical performance is required.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturing (AM)ceramicsnanocompositespolyamide 12 (PA12)silicon nitride (Si3N4)three-dimensional (3D) printing

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Hellenic Mediterranean University, 71410 Heraklion, Greece.
  • Department of Industrial Engineering and Management, International Hellenic University, 14th km Thessaloniki-N. Moudania, Thermi, 57001 Thessaloniki, Greece.
  • Physical Metallurgy Laboratory, Mechanical Engineering Department, School of Engineering, Aristotle University of Thessaloniki, 54124 Thessaloniki, Greece.
  • Centre for Research & Development of Advanced Materials (CERDAM), Balkan Centre, Building B', 10th km, Thessaloniki-Thermi Road, 57001 Thessaloniki, Greece.
  • Department of Industrial Design and Production Engineering, University of West Attica, 12243 Athens, Greece.
  • Department of Materials Science and Technology, University of Crete, 70013 Heraklion, Greece.

ORCID-Profile: Markos Petousis, Apostolos Korlos, Nikolaos Michailidis, Vassilis M Papadakis, Apostolos Argyros, Nikolaos Mountakis, Maria Spyridaki, Athena Maniadi

Zitieren

APA

Petousis, M., Korlos, A., Michailidis, N., Papadakis, V. M., Argyros, A., Mountakis, N., Spyridaki, M., Maniadi, A., Moutsopoulou, A., & Vidakis, N. (2025). Optimization of Silicon Nitride Nanopowder Content in Polyamide 12 (PA12) in Extrusion-Based Additive Manufacturing. Nanomaterials, 16(1), 47. https://doi.org/10.3390/nano16010047

Vancouver

Petousis M, Korlos A, Michailidis N, Papadakis VM, Argyros A, Mountakis N, et al. Optimization of Silicon Nitride Nanopowder Content in Polyamide 12 (PA12) in Extrusion-Based Additive Manufacturing. Nanomaterials. 2025;16(1):47. doi:10.3390/nano16010047

BibTeX
@article{Petousis2025,
  author = {Petousis, Markos and Korlos, Apostolos and Michailidis, Nikolaos and Papadakis, Vassilis M and Argyros, Apostolos and Mountakis, Nikolaos and Spyridaki, Maria and Maniadi, Athena and Moutsopoulou, Amalia and Vidakis, Nectarios},
  title = {Optimization of Silicon Nitride Nanopowder Content in Polyamide 12 (PA12) in Extrusion-Based Additive Manufacturing},
  journal = {Nanomaterials},
  year = {2025},
  volume = {16},
  number = {1},
  pages = {47},
  doi = {10.3390/nano16010047}
}
Kostenlos starten →