A Flexible Pressure Sensor Based on Graphene/Epoxy Resin Composite Film and Screen Printing Process
Nanomaterials · 24.09.2023 · 13 (19) · 2630
DOI: 10.3390/nano13192630 ↗Kurz gefasst
Fachartikel in der Zeitschrift Nanomaterials, online erschienen am 24.09.2023. Verfasst von Qijing Lin und 7 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Mechanical Manufacturing Systems Engineering, Xi'an Jiaotong University, Xi'an 710049, China. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 61 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program, National Natural Science Foundation of China, Natural Science Foundation of Chongqing City.
Abstract (Originalsprache)
At present, flexible pressure-sensitive materials generally have problems with weak adhesion and poor wear resistance, which easily result in friction failure when used for plantar pressure detection. In this study, a flexible pressure sensor with the advantages of a wide detection range, fast recovery, and good abrasive resistance was designed and prepared based on the screen printing process. The pressure-sensitive unit with a structural size of 5 mm× 8 mm was a functional material system due to the use of graphene and epoxy resin. The influence of the different mass ratios of the graphene and epoxy resin on the sensing properties was also studied. The test results showed that when the mass ratio of graphene to epoxy resin was 1:4, the response time and recovery time of the sensing unit were 40.8 ms and 3.7 ms, respectively, and the pressure detection range was 2.5–500 kPa. The sensor can detect dynamic pressure at 0.5 Hz, 1 Hz, 2 Hz, 10 Hz, and 20 Hz and can withstand 11,000 cycles of bending. In addition, adhesion tests showed that the high viscosity of the epoxy helped to improve the interlayer bond between the pressure-sensitive materials and the flexible substrate, which makes it more suitable for plantar pressure detection environments, where friction is common.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- State Key Laboratory of Mechanical Manufacturing Systems Engineering, Xi'an Jiaotong University, Xi'an 710049, China.
- School of Mechanical and Manufacturing Engineering, Xiamen Institute of Technology, Xiamen 361021, China.
- Chongqing Academician Workstation, Chongqing 2011 Collaborative Innovation Centers of Micro/Nano Sensing and Intelligent Ecological Internet of Things, Chongqing Key Laboratory of Micro-Nano Systems and Intelligent Sens…
- Shandong Laboratory of Yantai Advanced Materials and Green Manufacturing, Yantai 265503, China.
- Xi'an Jiaotong University (Yantai) Research Institute for Intelligent Sensing Technology and System, Xi'an Jiaotong University, Xi'an 710049, China.
ORCID-Profile: Fuzheng Zhang, Qi Mao
Förderung
- National Key Research and Development Program
- National Natural Science Foundation of China
- Natural Science Foundation of Chongqing City
- Postdoctoral Innovation Talents Support Program
Zitieren
APA
Lin, Q., Zhang, F., Xu, X., Yang, H., Mao, Q., Xian, D., Yao, K., & Meng, Q. (2023). A Flexible Pressure Sensor Based on Graphene/Epoxy Resin Composite Film and Screen Printing Process. Nanomaterials, 13(19), 2630. https://doi.org/10.3390/nano13192630
Vancouver
Lin Q, Zhang F, Xu X, Yang H, Mao Q, Xian D, et al. A Flexible Pressure Sensor Based on Graphene/Epoxy Resin Composite Film and Screen Printing Process. Nanomaterials. 2023;13(19):2630. doi:10.3390/nano13192630
BibTeX
@article{Lin2023,
author = {Lin, Qijing and Zhang, Fuzheng and Xu, Xiangyue and Yang, Haolin and Mao, Qi and Xian, Dan and Yao, Kun and Meng, Qingzhi},
title = {A Flexible Pressure Sensor Based on Graphene/Epoxy Resin Composite Film and Screen Printing Process},
journal = {Nanomaterials},
year = {2023},
volume = {13},
number = {19},
pages = {2630},
doi = {10.3390/nano13192630}
}
EUVIMED