Effects of Nano-CeO2 on Microstructure and Properties of WC/FeCoNiCrMo0.2 Composite High Entropy Alloy Coatings by Laser Cladding
Nanomaterials · 19.03.2023 · 13 (6) · 1104
DOI: 10.3390/nano13061104 ↗Kurz gefasst
Fachartikel in der Zeitschrift Nanomaterials, online erschienen am 19.03.2023. Verfasst von Xiangyu Ren und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Xinjiang University, Wulumuqi 830047, China. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Wenlei Sun, Xinjiang Autonomous Region Key Research and Development Project, Key Laboratory Opening Foundation of Xinjiang Autonomous Region.
Abstract (Originalsprache)
FeCoNiCrMo0.2 high entropy alloy has many excellent properties, such as high strength, high wear resistance, high corrosion resistance, and high ductility. To further improve the properties of this coating, FeCoNiCrMo high entropy alloy (HEA) coatings, and two composite coatings, FeCoNiCrMo0.2 + WC and FeCoNiCrMo0.2 + WC + CeO2, were prepared on the surface of 316L stainless steel by laser cladding technology. After adding WC ceramic powder and CeO2 rare earth control, the microstructure, hardness, wear resistance, and corrosion resistance of the three coatings were carefully studied. The results show that WC powder significantly improved the hardness of the HEA coating and reduced the friction factor. The FeCoNiCrMo0.2 + 32%WC coating showed excellent mechanical properties, but the distribution of hard phase particles in the coating microstructure was uneven, resulting in unstable distribution of hardness and wear resistance in each region of the coating. After adding 2% nano-CeO2 rare earth oxide, although the hardness and friction factor decreased slightly compared with the FeCoNiCrMo0.2 + 32%WC coating, the coating grain structure was finer, which reduced the porosity and crack sensitivity of the coating, and the phase composition of the coating did not change; there was a uniform hardness distribution, a more stable friction coefficient, and the flattest wear morphology. In addition, under the same corrosive environment, the value of polarization impedance of the FeCoNiCrMo0.2 + 32%WC + 2%CeO2 coating was greater, the corrosion rate was relatively low, and the corrosion resistance was better. Therefore, based on various indexes, the FeCoNiCrMo0.2 + 32%WC + 2%CeO2 coating has the best comprehensive performance and can extend the service life of 316L workpieces.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- College of Mechanical Engineering, Xinjiang University, Wulumuqi 830047, China.
Förderung
- Wenlei Sun
- Xinjiang Autonomous Region Key Research and Development Project
- Key Laboratory Opening Foundation of Xinjiang Autonomous Region
- University Science Research Planning Project of Xinjiang Autonomous Region
Zitieren
APA
Ren, X., Sun, W., Sheng, Z., Liu, M., Hui, H., & Xiao, Y. (2023). Effects of Nano-CeO2 on Microstructure and Properties of WC/FeCoNiCrMo0.2 Composite High Entropy Alloy Coatings by Laser Cladding. Nanomaterials, 13(6), 1104. https://doi.org/10.3390/nano13061104
Vancouver
Ren X, Sun W, Sheng Z, Liu M, Hui H, Xiao Y. Effects of Nano-CeO2 on Microstructure and Properties of WC/FeCoNiCrMo0.2 Composite High Entropy Alloy Coatings by Laser Cladding. Nanomaterials. 2023;13(6):1104. doi:10.3390/nano13061104
BibTeX
@article{Ren2023,
author = {Ren, Xiangyu and Sun, Wenlei and Sheng, Zefeng and Liu, Minying and Hui, Hujing and Xiao, Yi},
title = {Effects of Nano-CeO2 on Microstructure and Properties of WC/FeCoNiCrMo0.2 Composite High Entropy Alloy Coatings by Laser Cladding},
journal = {Nanomaterials},
year = {2023},
volume = {13},
number = {6},
pages = {1104},
doi = {10.3390/nano13061104}
}
EUVIMED