EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Effect of Electropulsing-Assisted Ultrasonic Surface Rolling Process on the Friction and Wear Properties of AA 2024-T3

Daoyin Xin, Guangjun Chen, Yuhang Liang, Wenqi Wang, Chuan He, Yingxin Lv, Bo Zhang, Jiashuai Huang

Micromachines · 28.05.2026 · 17 (6) · 665

DOI: 10.3390/mi17060665 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 28.05.2026. Verfasst von Daoyin Xin und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Tianjin Municipal Education Commission, Scientific Research Project of Tianjin Municipal Education Commission, Tianjin Science and Technology Plan Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aluminum alloy (AA) 2024-T3 is widely used in the aerospace industry due to its high specific strength and superior fatigue resistance, yet its moderate hardness and inadequate wear resistance fail to meet service demands under severe wear conditions. Although the electropulsing-assisted ultrasonic surface rolling process (EP-USRP) can strengthen its surface, the mechanism by which pulsed current density influences the friction and wear properties of the strengthened layer remains unclear. This study employed EP-USRP to strengthen the surface properties of AA 2024-T3, systematically examining the impacts of different pulsed current densities on its surface morphology, roughness, microhardness, and tribological performance, while comparing wear mechanisms among differently treated samples under various normal loads. The results indicate that EP-USRP can improve the surface mechanical properties compared with USRP. At 1.42 A/mm2 current density, the EP-USRP-3 sample achieved 27.7% lower surface roughness and 19.6% higher microhardness. Under a 2 N normal load, its average friction coefficient, wear volume, and wear rate decreased by 5.34%, 36.28%, and 36.27%, respectively. Adhesive and oxidative wear, coupled with material spalling, constitute its main wear behavior. The electroplastic effect induced by pulsed current may facilitate the increase in strain levels and dislocation densities, which could contribute to the improved surface mechanical and tribological properties of AA 2024-T3.

Schlagwörter

Stichwörter der Autor:innen

AA 2024-T3electropulsing-assisted ultrasonic surface rolling process (EP-USRP)friction and wear propertiesmicrohardnesssurface roughness

Autor:innen und Institutionen

  • School of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China.
  • Tianjin Key Laboratory of High Performance Manufacturing Technology and Equipment, Tianjin University of Technology and Education, Tianjin 300222, China.
  • School of Intelligent Engineering, Jiangsu Vocational College of Information Technology, Wuxi 214153, China.
  • School of Mechanical Engineering, Jiamusi University, Jiamusi 154007, China.

Förderung

  • Tianjin Municipal Education Commission
  • Scientific Research Project of Tianjin Municipal Education Commission
  • Tianjin Science and Technology Plan Project
  • Special Fund for Basic Scientific Research of Undergraduate Universities in Heilongjiang Province

Zitieren

APA

Xin, D., Chen, G., Liang, Y., Wang, W., He, C., Lv, Y., Zhang, B., & Huang, J. (2026). The Effect of Electropulsing-Assisted Ultrasonic Surface Rolling Process on the Friction and Wear Properties of AA 2024-T3. Micromachines, 17(6), 665. https://doi.org/10.3390/mi17060665

Vancouver

Xin D, Chen G, Liang Y, Wang W, He C, Lv Y, et al. The Effect of Electropulsing-Assisted Ultrasonic Surface Rolling Process on the Friction and Wear Properties of AA 2024-T3. Micromachines. 2026;17(6):665. doi:10.3390/mi17060665

BibTeX
@article{Xin2026,
  author = {Xin, Daoyin and Chen, Guangjun and Liang, Yuhang and Wang, Wenqi and He, Chuan and Lv, Yingxin and Zhang, Bo and Huang, Jiashuai},
  title = {The Effect of Electropulsing-Assisted Ultrasonic Surface Rolling Process on the Friction and Wear Properties of AA 2024-T3},
  journal = {Micromachines},
  year = {2026},
  volume = {17},
  number = {6},
  pages = {665},
  doi = {10.3390/mi17060665}
}
Kostenlos starten →