EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evaluation of 3D-Printed Dry Electrodes for Surface Electromyography in Dynamic Muscle Assessment

Ahmad O Alokaily iD, Ahmed A Aldohbeyb iD, Mohamed A Almadi iD, Fahed K Alnawfal, Shahad N Alshamlan iD, Suhail S Alshahrani iD, Khalid Alhussaini iD, Alaa M Albishi iD, Khalid I Aloraini, Ahmad Zahid Rao iD, Ziyad Aloqalaa iD

Micromachines · 22.04.2026 · 17 (5) · 504

DOI: 10.3390/mi17050504 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 22.04.2026. Verfasst von Ahmad O Alokaily und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Technology, College of Applied Medical Sciences, King Saud University, P.O. Box 10219, Riyadh 11433, Saudi Arabia. Die Arbeit nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Ongoing Research Funding program, King Saud University, Riyadh, Saudi Arabia, King Saud University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Surface electromyography (sEMG) is widely used to assess muscle activity in clinical and research settings. However, while conventional wet electrodes have advanced considerably in recent years, they are often limited by disposability, reduced comfort, and limited reusability. Recent advances in additive manufacturing provide opportunities to fabricate customizable, low-cost dry electrodes using conductive filaments. This study aimed to evaluate the feasibility and signal performance of in-house-fabricated 3D-printed sEMG electrodes made from three commercially available conductive filaments, (Fili, Filaflex, and Proto-Pasta) differing in base polymer and resistivity, and compared their performance with standard wet electrodes. Surface electrodes were placed over the biceps brachii muscle, and EMG signals were recorded during concentric–eccentric elbow flexion under three loading conditions (3, 5, and 7 kg). Signal quality was assessed using EMG amplitude, signal-to-noise ratio (SNR), and background noise. The results showed no significant differences in SNR or background noise between the 3D-printed electrodes and standard wet electrodes. Among the tested materials, Proto-Pasta electrodes produced the highest mean EMG amplitudes, while Filaflex electrodes showed slightly lower background noise, although these differences were not statistically significant. Overall, the findings indicate that in-house-fabricated 3D-printed electrodes can provide signal quality comparable to conventional wet electrodes, supporting their potential use as low-cost and customizable alternatives for sEMG applications in research and wearable monitoring systems.

Schlagwörter

Stichwörter der Autor:innen

3D-printed electrodesadditive manufacturingconductive filamentssignal qualitysurface electromyography (sEMG)

Autor:innen und Institutionen

  • Department of Biomedical Technology, College of Applied Medical Sciences, King Saud University, P.O. Box 10219, Riyadh 11433, Saudi Arabia.
  • Department of Rehabilitation Health Sciences, College of Applied Medical Sciences, King Saud University, P.O. Box 10219, Riyadh 11433, Saudi Arabia.
  • Department of Physical Medicine and Rehabilitation, McGovern Medical School, University of Texas Health Science Center at Houston, Houston, TX 77030, USA.

ORCID-Profile: Ahmad O Alokaily, Ahmed A Aldohbeyb, Mohamed A Almadi, Shahad N Alshamlan, Suhail S Alshahrani, Khalid Alhussaini, Alaa M Albishi, Ahmad Zahid Rao, Ziyad Aloqalaa

Förderung

  • The Ongoing Research Funding program, King Saud University, Riyadh, Saudi Arabia
  • King Saud University

Zitieren

APA

Alokaily, A. O., Aldohbeyb, A. A., Almadi, M. A., Alnawfal, F. K., Alshamlan, S. N., Alshahrani, S. S., Alhussaini, K., Albishi, A. M., Aloraini, K. I., Rao, A. Z., & Aloqalaa, Z. (2026). Evaluation of 3D-Printed Dry Electrodes for Surface Electromyography in Dynamic Muscle Assessment. Micromachines, 17(5), 504. https://doi.org/10.3390/mi17050504

Vancouver

Alokaily AO, Aldohbeyb AA, Almadi MA, Alnawfal FK, Alshamlan SN, Alshahrani SS, et al. Evaluation of 3D-Printed Dry Electrodes for Surface Electromyography in Dynamic Muscle Assessment. Micromachines. 2026;17(5):504. doi:10.3390/mi17050504

BibTeX
@article{Alokaily2026,
  author = {Alokaily, Ahmad O and Aldohbeyb, Ahmed A and Almadi, Mohamed A and Alnawfal, Fahed K and Alshamlan, Shahad N and Alshahrani, Suhail S and Alhussaini, Khalid and Albishi, Alaa M and Aloraini, Khalid I and Rao, Ahmad Zahid and Aloqalaa, Ziyad},
  title = {Evaluation of 3D-Printed Dry Electrodes for Surface Electromyography in Dynamic Muscle Assessment},
  journal = {Micromachines},
  year = {2026},
  volume = {17},
  number = {5},
  pages = {504},
  doi = {10.3390/mi17050504}
}
Kostenlos starten →