EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Low-Loss Multimode Waveguide Bends with Direct Laser Writing in Polymer

Tigran Baghdasaryan iD, Neshteh Kourian, Mushegh Rafayelyan iD, Tatevik Sarukhanyan iD

Micromachines · 29.11.2025 · 16 (12) · 1361

DOI: 10.3390/mi16121361 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 29.11.2025. Verfasst von Tigran Baghdasaryan und 3 weiteren Autor:innen. Beteiligte Einrichtung: Vrije Universiteit Brussel, Department of Applied Physics and Photonics, Brussels Photonics, Pleinlaan 2, 1050 Brussel, Belgium. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Higher Education and Science Committee of the Republic of Armenia, Interreg, Research Foundation - Flanders.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Waveguide bends are critical components for compact routing in integrated photonic circuits, yet their design in air-clad polymer waveguides fabricated by two-photon polymerization direct laser writing (2PP-DLW) is challenging due to multimode behavior. We address this by systematically modeling Bézier-shaped 90° bends and S-bends using a variational FDTD solver, exploring bend span, curvature, and waveguide dimensions. Our results show that smaller waveguides (widths 2–4 µm) and lower Bézier parameters (B = 0–0.2) consistently yield superior performance, enabling sharper bends with minimal loss. For 90° bends, spans as small as 20–30 µm achieve near-unity transmission, while for S-bends, aspect ratios below 1 are feasible, allowing highly compact layouts. Although all configurations transmit energy to the fundamental mode, wider waveguides exhibit stronger higher-order mode excitation and greater sensitivity to fabrication imperfections. Smaller waveguides reduce these effects but approach the resolution limits of 2PP-DLW. Thus, a 2 µm wide waveguide represents an optimal compromise between fabrication feasibility and optical performance. Experimental demonstrations confirm the practicality of these design rules, illustrating trends predicted by simulations. These findings establish clear guidelines for designing low-loss, space-efficient 3D photonic circuits and highlight the critical role of simulation-driven optimization in fully exploiting 2PP-DLW technology, while providing deeper insight for future device architectures.

Schlagwörter

Stichwörter der Autor:innen

2 photon polymerizationBézier shape bendsdirect laser writingmultimode waveguides

Autor:innen und Institutionen

  • Vrije Universiteit Brussel, Department of Applied Physics and Photonics, Brussels Photonics, Pleinlaan 2, 1050 Brussel, Belgium.
  • PhotonicsAI Lab, Institute of Physics, Yerevan State University, 1 Alex Manoogian, Yerevan 0025, Armenia.

ORCID-Profile: Tigran Baghdasaryan, Mushegh Rafayelyan, Tatevik Sarukhanyan

Förderung

  • Higher Education and Science Committee of the Republic of Armenia
  • Interreg
  • Research Foundation - Flanders
  • Research Foundation—Flanders—Fonds Wetenschappelijk Onderzoek—FWO
  • COST
  • Herculesstichting
  • Methusalem foundation
  • Industrial Research Fund (IOF) and OZR of the Vrije Universiteit Brussel

Zitieren

APA

Baghdasaryan, T., Kourian, N., Rafayelyan, M., & Sarukhanyan, T. (2025). Low-Loss Multimode Waveguide Bends with Direct Laser Writing in Polymer. Micromachines, 16(12), 1361. https://doi.org/10.3390/mi16121361

Vancouver

Baghdasaryan T, Kourian N, Rafayelyan M, Sarukhanyan T. Low-Loss Multimode Waveguide Bends with Direct Laser Writing in Polymer. Micromachines. 2025;16(12):1361. doi:10.3390/mi16121361

BibTeX
@article{Baghdasaryan2025,
  author = {Baghdasaryan, Tigran and Kourian, Neshteh and Rafayelyan, Mushegh and Sarukhanyan, Tatevik},
  title = {Low-Loss Multimode Waveguide Bends with Direct Laser Writing in Polymer},
  journal = {Micromachines},
  year = {2025},
  volume = {16},
  number = {12},
  pages = {1361},
  doi = {10.3390/mi16121361}
}
Kostenlos starten →