Sintering for High Power Optoelectronic Devices
Micromachines · 14.10.2025 · 16 (10) · 1164
DOI: 10.3390/mi16101164 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 14.10.2025. Verfasst von Hannes Schwan und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute for Innovative Mobility (IIMo), University of Applied Science Ingolstadt, Esplanade 10, 85049 Ingolstadt, Germany. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bundesministerium für Forschung, Technologie und Raumfahrt.
Abstract (Originalsprache)
Residual-free eutectic Au80Sn20 soldering is still the dominant assembly technology for optoelectronic devices such as high-power lasers, LEDs, and photodiodes. Due to the high cost of gold, alternatives are desirable. This paper investigates the thermal performance of copper-based sintering for optoelectronic submodules on first and second level to obtain thermally efficient thin bondlines. Sintered interconnects obtained by a new particle-free copper ink, based on complexed copper salt, are compared with copper flake and silver nanoparticle sintered interconnects and benchmarked against AuSn solder interconnects. The copper ink is dispensed and predried at 130 °C to facilitate in situ generation of Cu nanoparticles by thermal decomposition of the metal salt before sintering. Submounts are then sintered at 275 °C for 15 min under nitrogen with 30 MPa pressure, forming uniform 2–5 µm copper layers achieving shear strengths above 31 MPa. Unpackaged LEDs are bonded on first level using the copper ink but applying only 10 MPa to avoid damaging the semiconductor dies. Thermal performance is evaluated via transient thermal analysis. Results show that copper ink interfaces approach the performance of thin AuSn joints and match silver interconnects at second level. However, at first level, AuSn and sintered interconnects of commercial silver and copper pastes remained superior due to the relative inhomogeneous thickness of the thin Cu copper layer after predrying, requiring higher bonding pressure to equalize surface inhomogeneities.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Institute for Innovative Mobility (IIMo), University of Applied Science Ingolstadt, Esplanade 10, 85049 Ingolstadt, Germany.
- R&D Produkt Integration Backend, ams-OSRAM International GmbH, Leibnizstraße 4, 93055 Regensburg, Germany.
ORCID-Profile: Hannes Schwan, Nihesh Mohan, Maximilian Schmid, Gordon Elger
Förderung
- Bundesministerium für Forschung, Technologie und Raumfahrt
Zitieren
APA
Schwan, H., Mohan, N., Schmid, M., Saha, R. K., Klassen, H., Müller, K., & Elger, G. (2025). Sintering for High Power Optoelectronic Devices. Micromachines, 16(10), 1164. https://doi.org/10.3390/mi16101164
Vancouver
Schwan H, Mohan N, Schmid M, Saha RK, Klassen H, Müller K, et al. Sintering for High Power Optoelectronic Devices. Micromachines. 2025;16(10):1164. doi:10.3390/mi16101164
BibTeX
@article{Schwan2025,
author = {Schwan, Hannes and Mohan, Nihesh and Schmid, Maximilian and Saha, Rocky Kumar and Klassen, Holger and Müller, Klaus and Elger, Gordon},
title = {Sintering for High Power Optoelectronic Devices},
journal = {Micromachines},
year = {2025},
volume = {16},
number = {10},
pages = {1164},
doi = {10.3390/mi16101164}
}
EUVIMED