Study on the Motion Trajectory of Abrasives and Surface Improvement Mechanism in Ultrasonic-Assisted Diamond Wire Sawing Monocrystalline Silicon
Micromachines · 13.06.2025 · 16 (6) · 708
DOI: 10.3390/mi16060708 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 13.06.2025. Verfasst von Honghao Li und 3 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory of High Efficiency and Clean Mechanical Manufacture of Ministry of Education, School of Mechanical Engineering, Shandong University, J…. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Project, Natural Science Foundation of Shandong Province.
Abstract (Originalsprache)
The surface quality of diamond wire sawing (DWS) wafers directly affects the efficiency and yield of subsequent processing steps. This paper investigates the motion trajectory of abrasives in ultrasonic-assisted diamond wire sawing (UADWS) and its mechanism for improving surface quality. The influence of ultrasonic vibration on the cutting arc length, cutting depth, and interference of multi-abrasive trajectories was analyzed through the establishment of an abrasive motion trajectory model. The ultrasonic vibration transforms the abrasive trajectory from linear to sinusoidal, thereby increasing the cutting arc length while reducing the cutting depth. A lower wire speed was found to be more conducive to exploiting the advantages of ultrasonic vibration. Furthermore, the intersecting interference of multi-abrasive trajectories contributes to enhanced surface quality. Experimental studies were conducted on monocrystalline silicon (mono-Si) to verify the effectiveness of ultrasonic vibration in improving surface morphology and reducing wire marks during the sawing process. The experimental results demonstrate that, compared with DWS, UADWS achieves a significantly lower surface roughness Ra and generates micro-pits. The ultrasonic vibration induces a micro-grinding effect on both peaks and valleys of wire marks, effectively reducing their peak–valley (PV) height. This study provides a theoretical basis for optimizing UADWS process parameters and holds significant implications for improving surface quality in mono-Si wafer slicing.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Key Laboratory of High Efficiency and Clean Mechanical Manufacture of Ministry of Education, School of Mechanical Engineering, Shandong University, Jinan 250061, China.
- State Key Laboratory of Advanced Equipment and Technology for Metal Forming, Shandong University, Jinan 250061, China.
- Shandong Key Laboratory of High Performance Tools and System, Shandong University, Jinan 250061, China.
Förderung
- National Key Research and Development Project
- Natural Science Foundation of Shandong Province
Zitieren
APA
Li, H., Gao, Y., Hu, S., & Huo, Z. (2025). Study on the Motion Trajectory of Abrasives and Surface Improvement Mechanism in Ultrasonic-Assisted Diamond Wire Sawing Monocrystalline Silicon. Micromachines, 16(6), 708. https://doi.org/10.3390/mi16060708
Vancouver
Li H, Gao Y, Hu S, Huo Z. Study on the Motion Trajectory of Abrasives and Surface Improvement Mechanism in Ultrasonic-Assisted Diamond Wire Sawing Monocrystalline Silicon. Micromachines. 2025;16(6):708. doi:10.3390/mi16060708
BibTeX
@article{Li2025,
author = {Li, Honghao and Gao, Yufei and Hu, Shengtan and Huo, Zhipu},
title = {Study on the Motion Trajectory of Abrasives and Surface Improvement Mechanism in Ultrasonic-Assisted Diamond Wire Sawing Monocrystalline Silicon},
journal = {Micromachines},
year = {2025},
volume = {16},
number = {6},
pages = {708},
doi = {10.3390/mi16060708}
}
EUVIMED