EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Assessment of Local Geometric Uncertainties in Polysilicon MEMS: A Genetic Algorithm and POD-Kriging Surrogate Modeling Approach

Ananya Roy, Francesco Rizzini, Gabriele Gattere, Carlo Valzasina, Aldo Ghisi iD, Stefano Mariani iD

Micromachines · 23.01.2025 · 16 (2) · 127

DOI: 10.3390/mi16020127 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 23.01.2025. Verfasst von Ananya Roy und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil and Environmental Engineering, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano, Italy. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The project was funded by STMicroelectronics within the Joint Research Platform STEAM, project P5 "Reliability of MEMS"., STMicroelectronics.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

On the way toward MEMS miniaturization, the quantification of geometric uncertainties stands as a primary challenge. In this paper, an approach that combines genetic algorithms and proper orthogonal decomposition with kriging surrogate modeling was proposed to accurately predict over-etch measures through an on-chip test device. Despite being fabricated on a single wafer under nominally identical manufacturing conditions, MEMS can display different responses under the same actuation, due to a different characteristic geometry. It is shown that the uncertainties, given in terms of over-etch values, were not only different from die to die but also within the same die, depending on the local geometric features of the device. Therefore, the proposed method provided an alternative solution to estimate the uncertainties in MEMS devices, relying only on the capacitance–voltage response. A statistical analysis was carried out based on a batch of devices tested in the laboratory. These tests and the estimation procedure allowed us to quantify the mean values of the over-etch relative to the target as +12.2 % at comb fingers, +10.0 % at the supporting springs, and −4.8 % at stoppers, showing noteworthy variability induced by the environment.

Schlagwörter

Stichwörter der Autor:innen

genetic algorithm (GA)kriging interpolationmicro electro-mechanical systems (MEMS)over-etchingproper orthogonal decomposition (POD)uncertainty quantification

Autor:innen und Institutionen

  • Department of Civil and Environmental Engineering, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano, Italy.
  • STMicroelectronics, Via Tolomeo 1, 20010 Cornaredo, Italy.

ORCID-Profile: Aldo Ghisi, Stefano Mariani

Förderung

  • The project was funded by STMicroelectronics within the Joint Research Platform STEAM, project P5 "Reliability of MEMS".
  • STMicroelectronics

Zitieren

APA

Roy, A., Rizzini, F., Gattere, G., Valzasina, C., Ghisi, A., & Mariani, S. (2025). An Assessment of Local Geometric Uncertainties in Polysilicon MEMS: A Genetic Algorithm and POD-Kriging Surrogate Modeling Approach. Micromachines, 16(2), 127. https://doi.org/10.3390/mi16020127

Vancouver

Roy A, Rizzini F, Gattere G, Valzasina C, Ghisi A, Mariani S. An Assessment of Local Geometric Uncertainties in Polysilicon MEMS: A Genetic Algorithm and POD-Kriging Surrogate Modeling Approach. Micromachines. 2025;16(2):127. doi:10.3390/mi16020127

BibTeX
@article{Roy2025,
  author = {Roy, Ananya and Rizzini, Francesco and Gattere, Gabriele and Valzasina, Carlo and Ghisi, Aldo and Mariani, Stefano},
  title = {An Assessment of Local Geometric Uncertainties in Polysilicon MEMS: A Genetic Algorithm and POD-Kriging Surrogate Modeling Approach},
  journal = {Micromachines},
  year = {2025},
  volume = {16},
  number = {2},
  pages = {127},
  doi = {10.3390/mi16020127}
}
Kostenlos starten →