Design of Interface ASIC with Power-Saving Switches for Capacitive Accelerometers
Micromachines · 15.01.2025 · 16 (1) · 96
DOI: 10.3390/mi16010096 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 15.01.2025. Verfasst von Juncheng Cai und 6 weiteren Autor:innen. Beteiligte Einrichtung: Hangzhou Sotry Automatic Control Tech Co., Ltd., Hangzhou 311112, China. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science and Technology Project of Zhejiang Province, Natural Science Foundation of Ningbo under Grant, National Natural Science Foundation of China.
Abstract (Originalsprache)
High-precision, low-power MEMS accelerometers are extensively utilized across civilian applications. Closed-loop accelerometers employing switched-capacitor (SC) circuit topologies offer notable advantages, including low power consumption, high signal-to-noise ratio (SNR), and excellent linearity. Addressing the critical demand for high-precision, low-power MEMS accelerometers in modern geophones, this work focuses on the design and implementation of closed-loop interface ASICs (Application-Specific Integrated Circuits). The proposed interface circuit, based on switched-capacitor modulation technology, incorporates a low-noise charge amplifier, sample-and-hold circuit, integrator, and clock divider circuit. To minimize average power consumption, a switched operational amplifier (op-amp) technique is adopted, which temporarily disconnects idle op-amps from the power supply. Additionally, a class-AB output stage is employed to enhance the dynamic range of the circuit. The design was realized using a standard 0.35 μm CMOS process, culminating in the completion of layout design and small-scale engineering fabrication. The performance of the MEMS accelerometers was evaluated under a 3.3 V power supply, achieving a power consumption of 3.3 mW, an accelerometer noise density below 1 μg/√Hz, a sensitivity of 1.65 V/g, a measurement range of ±1 g, a nonlinearity of 0.15%, a bandwidth of 300 Hz, and a bias stability of approximately 36 μg. These results demonstrate the efficacy of the proposed design in meeting the stringent requirements of high-precision MEMS accelerometer applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Hangzhou Sotry Automatic Control Tech Co., Ltd., Hangzhou 311112, China.
- College of Electrical and Electronic Engineering, Wenzhou University, Wenzhou 325035, China.
- Ningbo Institute of Digital Twin, Eastern Institute of Technology, Ningbo 315042, China.
- Faculty of Electrical Engineering and Computer Science, Ningbo University, Ningbo 315211, China.
- Shanghai Aerospace Control Technology Institute, Shanghai 201109, China.
ORCID-Profile: Yongbin Cai, Xiaowei Zhang
Förderung
- Science and Technology Project of Zhejiang Province
- Natural Science Foundation of Ningbo under Grant
- National Natural Science Foundation of China
- Natural Science Foundation of Ningbo
Zitieren
APA
Cai, J., Cai, Y., Li, X., Wang, S., Zhang, X., Di, X., & Wang, P. (2025). Design of Interface ASIC with Power-Saving Switches for Capacitive Accelerometers. Micromachines, 16(1), 96. https://doi.org/10.3390/mi16010096
Vancouver
Cai J, Cai Y, Li X, Wang S, Zhang X, Di X, et al. Design of Interface ASIC with Power-Saving Switches for Capacitive Accelerometers. Micromachines. 2025;16(1):96. doi:10.3390/mi16010096
BibTeX
@article{Cai2025,
author = {Cai, Juncheng and Cai, Yongbin and Li, Xiangyu and Wang, Shanshan and Zhang, Xiaowei and Di, Xinpeng and Wang, Pengjun},
title = {Design of Interface ASIC with Power-Saving Switches for Capacitive Accelerometers},
journal = {Micromachines},
year = {2025},
volume = {16},
number = {1},
pages = {96},
doi = {10.3390/mi16010096}
}
EUVIMED