EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Comparative Analysis of Laser-Ablated Surface Characteristics Between the Si Face and C Face of Silicon Carbide Substrates

Hsin-Yi Tsai iD, Yu-Hsuan Lin, Kuo-Cheng Huang, J Andrew Yeh iD, Yi Yang iD, Chien-Fang Ding iD

Micromachines · 01.01.2025 · 16 (1) · 62

DOI: 10.3390/mi16010062 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 01.01.2025. Verfasst von Hsin-Yi Tsai und 5 weiteren Autor:innen. Beteiligte Einrichtung: Taiwan Instrument Research Institute, National Applied Research Laboratories, Hsinchu 300092, Taiwan. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Anton Paar Inc., DEUVtek Co., Ltd..

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Silicon carbide (SiC) has significant potential as a third-generation semiconductor material due to its exceptional thermal and electronic properties, yet its high hardness and brittleness make processing costly and complex. This study introduces ultraviolet laser ablation as a method for direct SiC material removal, investigating the effects of varying scanning speeds on surface composition, hardness, and ablation depth. The results indicate optimal processing speeds for the Si and C faces at 200 mm/s and 100 mm/s, respectively. Ablation depth is linearly correlated with laser repetitions, achieving a 25% improvement in removal efficiency at 100 mm/s on the C face compared to higher speeds. A composition analysis shows that the Si and C faces of SiC exhibit consistent ratios of Si, O, and C both before and after ablation. Post-ablation, the proportion of Si and C decreases with an increased presence of oxygen. At scanning speeds below 200 mm/s, the variation in speed has minimal effect on the compositional ratios, indicating a stable elemental distribution across the surface despite differences in processing speed. Hardness testing indicates an initial hardness of 13,896 MPa for the C face, higher than that of the Si face, with both surfaces experiencing a drop to less than 1% of their original hardness (below 50 MPa) after ablation. Lattice structure analysis shows Moissanite-5H SiC and cubic silicon formation on the Si face, while the C face retains partial SiC structure. This study found that when laser parameters are used to process SiC, the processing parameters required on both sides are different and provide important reference information for future industrial processing applications to shorten the time and process cost of SiC surface thinning.

Schlagwörter

Stichwörter der Autor:innen

hardnessoxidationsilicon carbide (SiC)surface roughnessultraviolet laser

Autor:innen und Institutionen

  • Taiwan Instrument Research Institute, National Applied Research Laboratories, Hsinchu 300092, Taiwan.
  • Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu 300044, Taiwan.
  • Department of Biomechatronics Engineering, National Taiwan University, Taipei 106319, Taiwan.

ORCID-Profile: Hsin-Yi Tsai, J Andrew Yeh, Yi Yang, Chien-Fang Ding

Förderung

  • Anton Paar Inc.
  • DEUVtek Co., Ltd.

Zitieren

APA

Tsai, H. Y., Lin, Y. H., Huang, K. C., Yeh, J. A., Yang, Y., & Ding, C. F. (2025). A Comparative Analysis of Laser-Ablated Surface Characteristics Between the Si Face and C Face of Silicon Carbide Substrates. Micromachines, 16(1), 62. https://doi.org/10.3390/mi16010062

Vancouver

Tsai HY, Lin YH, Huang KC, Yeh JA, Yang Y, Ding CF. A Comparative Analysis of Laser-Ablated Surface Characteristics Between the Si Face and C Face of Silicon Carbide Substrates. Micromachines. 2025;16(1):62. doi:10.3390/mi16010062

BibTeX
@article{Tsai2025,
  author = {Tsai, Hsin-Yi and Lin, Yu-Hsuan and Huang, Kuo-Cheng and Yeh, J Andrew and Yang, Yi and Ding, Chien-Fang},
  title = {A Comparative Analysis of Laser-Ablated Surface Characteristics Between the Si Face and C Face of Silicon Carbide Substrates},
  journal = {Micromachines},
  year = {2025},
  volume = {16},
  number = {1},
  pages = {62},
  doi = {10.3390/mi16010062}
}
Kostenlos starten →