Determination of the Minimum Uncut Chip Thickness of Ti-6Al-4V Titanium Alloy Based on Dead Metal Zone
Micromachines · 29.11.2024 · 15 (12) · 1458
DOI: 10.3390/mi15121458 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 29.11.2024. Verfasst von Yaohui Zheng und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Engineering Training Center, Shenyang Aerospace University, Shenyang 110136, China. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Liaoning Provincial Department of Science and Technology, Basic Scientific Research Funds Project of the Education Department of Liaoning Province.
Abstract (Originalsprache)
In Ti-6Al-4V titanium alloy micro-machining, since the uncut chip thickness (UCT) is comparable to the radius of the tool cutting edge, there exists a minimum uncut chip thickness (MUCT), and when the UCT is smaller than the MUCT, the plowing effect dominates the cutting process, which seriously affects the machined surface quality and tool life. Therefore, the reliable prediction of the MUCT is of great significance. This paper used Deform to establish an orthogonal cutting simulation model, studied the effect of the dead metal zone (DMZ) on the micro-cutting material flow, determined the DMZ range, and proposed a new method for determining the MUCT based on the DMZ. Cutting experiments were conducted to verify the accuracy of the simulation model firstly by cutting force, and then confirming the accuracy of the DMZ-based MUCT determination method through chip analysis and surface quality analysis. Finally, the effects of different cutting conditions on DMZ and MUCT were further investigated using the proposed DMZ-based MUCT determination method. The results show that the MUCT of Ti-6Al-4V titanium alloy is 4.833 μm for a tool cutting edge radius of 40 μm and a cutting speed of 10 m/min. The DMZ boundary can be used as the boundary of micro-cutting plastic deformation, and the ratio of MUCT to cutting edge radius, hp/rn will gradually decrease with the increase in the tool cutting edge radius and the cutting speed.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Engineering Training Center, Shenyang Aerospace University, Shenyang 110136, China.
- Key Laboratory of Rapid Development & Manufacturing Technology for Aircraft, Shenyang Aerospace University, Ministry of Education, Shenyang 110136, China.
- School of Mechatronics Engineering, Shenyang Aerospace University, Shenyang 110136, China.
Förderung
- National Natural Science Foundation of China
- Liaoning Provincial Department of Science and Technology
- Basic Scientific Research Funds Project of the Education Department of Liaoning Province
Zitieren
APA
Zheng, Y., Huang, W., Liu, Y., Duan, P., & Wang, Y. (2024). Determination of the Minimum Uncut Chip Thickness of Ti-6Al-4V Titanium Alloy Based on Dead Metal Zone. Micromachines, 15(12), 1458. https://doi.org/10.3390/mi15121458
Vancouver
Zheng Y, Huang W, Liu Y, Duan P, Wang Y. Determination of the Minimum Uncut Chip Thickness of Ti-6Al-4V Titanium Alloy Based on Dead Metal Zone. Micromachines. 2024;15(12):1458. doi:10.3390/mi15121458
BibTeX
@article{Zheng2024,
author = {Zheng, Yaohui and Huang, Wentao and Liu, Yangyang and Duan, Pengchao and Wang, Yingxiao},
title = {Determination of the Minimum Uncut Chip Thickness of Ti-6Al-4V Titanium Alloy Based on Dead Metal Zone},
journal = {Micromachines},
year = {2024},
volume = {15},
number = {12},
pages = {1458},
doi = {10.3390/mi15121458}
}
EUVIMED