EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D-Printed Multi-Axis Alignment Airgap Dielectric Layer for Flexible Capacitive Pressure Sensor

Jeong-Beom Ko, Soo-Wan Kim, Hyeon-Beom Kim, Hyeon-Yun Jeong, Su-Yeong Moon, Young-Jin Yang

Micromachines · 31.10.2024 · 15 (11) · 1347

DOI: 10.3390/mi15111347 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 31.10.2024. Verfasst von Jeong-Beom Ko und 5 weiteren Autor:innen. Beteiligte Einrichtung: Clean Energy Transition Group, Korea Institute of Industrial Technology (KITECH), Jeju 63243, Republic of Korea. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Korea Institute of Industrial Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Flexible pressure sensors are increasingly recognized for their potential use in wearable electronic devices, attributed to their sensitivity and broad pressure response range. Introducing surface microstructures can notably enhance sensitivity; however, the pressure response range remains constrained by the limited volume of the compressible structure. To overcome this limitation, this study implements an aligned airgap structure fabricated using 3D printing technology. This structure, designed with a precisely aligned triaxial airgap configuration, offers high deformability under pressure, substantially broadening the pressure response range and improving sensitivity. This study analyzes the key structural parameters—the number of axes and pore size—that influence the compressibility and stability of the dielectric material. The results indicate that the capacitive pressure sensor with an aligned airgap structure, manufactured via 3D printing, exhibits a wide operating pressure range (50 Pa to 500 kPa), rapid response time (100 ms), wide limit of detection (50 Pa), and approximately 21 times enhancement in sensitivity (~0.019 kPa−1 within 100 kPa) compared with conventional bulk structures. Furthermore, foot pressure monitoring trials for wearable sensor applications demonstrated exceptional performance, indicating the sensor’s suitability as a wearable device for detecting plantar pressure. These findings advocate for the potential of 3D printing technology to supplant traditional sensor manufacturing processes.

Schlagwörter

Stichwörter der Autor:innen

3D printingalignment airgap dielectriccapacitive pressure sensorflexible sensor

Autor:innen und Institutionen

  • Clean Energy Transition Group, Korea Institute of Industrial Technology (KITECH), Jeju 63243, Republic of Korea.

Förderung

  • Korea Institute of Industrial Technology

Zitieren

APA

Ko, J. B., Kim, S. W., Kim, H. B., Jeong, H. Y., Moon, S. Y., & Yang, Y. J. (2024). 3D-Printed Multi-Axis Alignment Airgap Dielectric Layer for Flexible Capacitive Pressure Sensor. Micromachines, 15(11), 1347. https://doi.org/10.3390/mi15111347

Vancouver

Ko JB, Kim SW, Kim HB, Jeong HY, Moon SY, Yang YJ. 3D-Printed Multi-Axis Alignment Airgap Dielectric Layer for Flexible Capacitive Pressure Sensor. Micromachines. 2024;15(11):1347. doi:10.3390/mi15111347

BibTeX
@article{Ko2024,
  author = {Ko, Jeong-Beom and Kim, Soo-Wan and Kim, Hyeon-Beom and Jeong, Hyeon-Yun and Moon, Su-Yeong and Yang, Young-Jin},
  title = {3D-Printed Multi-Axis Alignment Airgap Dielectric Layer for Flexible Capacitive Pressure Sensor},
  journal = {Micromachines},
  year = {2024},
  volume = {15},
  number = {11},
  pages = {1347},
  doi = {10.3390/mi15111347}
}
Kostenlos starten →