Fabrication of Two-Layer Microfluidic Devices with Porous Electrodes Using Printed Sacrificial Layers
Micromachines · 22.08.2024 · 15 (8) · 1054
DOI: 10.3390/mi15081054 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 22.08.2024. Verfasst von Kosuke Ino und 6 weiteren Autor:innen. Beteiligte Einrichtung: Graduate School of Engineering, Tohoku University, 6-6-11-604 Aramaki-aza Aoba, Aoba-ku, Sendai 980-8579, Japan. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Japan Society for the Promotion of Science, Japan Agency for Medical Research and Development, AMED.
Abstract (Originalsprache)
Two-layer microfluidic devices with porous membranes have been widely used in bioapplications such as microphysiological systems (MPS). Porous electrodes, instead of membranes, have recently been incorporated into devices for electrochemical cell analysis. Generally, microfluidic channels are prepared using soft lithography and assembled into two-layer microfluidic devices. In addition to soft lithography, three-dimensional (3D) printing has been widely used for the direct fabrication of microfluidic devices because of its high flexibility. However, this technique has not yet been applied to the fabrication of two-layer microfluidic devices with porous electrodes. This paper proposes a novel fabrication process for this type of device. In brief, Pluronic F-127 ink was three-dimensionally printed in the form of sacrificial layers. A porous Au electrode, fabricated by sputtering Au on track-etched polyethylene terephthalate membranes, was placed between the top and bottom sacrificial layers. After covering with polydimethylsiloxane, the sacrificial layers were removed by flushing with a cold solution. To the best of our knowledge, this is the first report on the sacrificial approach-based fabrication of two-layer microfluidic devices with a porous electrode. Furthermore, the device was used for electrochemical assays of serotonin and could successfully measure concentrations up to 5 µM. In the future, this device can be used for MPS applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Graduate School of Engineering, Tohoku University, 6-6-11-604 Aramaki-aza Aoba, Aoba-ku, Sendai 980-8579, Japan.
- Graduate School of Environmental Studies, Tohoku University, 6-6-11-604 Aramaki-aza Aoba, Aoba-ku, Sendai 980-8579, Japan.
- Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, Sendai 980-8577, Japan.
- Frontier Research Institute for Interdisciplinary Sciences, Tohoku University, Aramaki-aza Aoba 6-3, Aoba-ku, Sendai 980-8578, Japan.
ORCID-Profile: Kosuke Ino, Hiroya Abe
Förderung
- Japan Society for the Promotion of Science
- Japan Agency for Medical Research and Development
- AMED
Zitieren
APA
Ino, K., Konno, A., Utagawa, Y., Kanno, T., Iwase, K., Abe, H., & Shiku, H. (2024). Fabrication of Two-Layer Microfluidic Devices with Porous Electrodes Using Printed Sacrificial Layers. Micromachines, 15(8), 1054. https://doi.org/10.3390/mi15081054
Vancouver
Ino K, Konno A, Utagawa Y, Kanno T, Iwase K, Abe H, et al. Fabrication of Two-Layer Microfluidic Devices with Porous Electrodes Using Printed Sacrificial Layers. Micromachines. 2024;15(8):1054. doi:10.3390/mi15081054
BibTeX
@article{Ino2024,
author = {Ino, Kosuke and Konno, An and Utagawa, Yoshinobu and Kanno, Taiyo and Iwase, Kazuyuki and Abe, Hiroya and Shiku, Hitoshi},
title = {Fabrication of Two-Layer Microfluidic Devices with Porous Electrodes Using Printed Sacrificial Layers},
journal = {Micromachines},
year = {2024},
volume = {15},
number = {8},
pages = {1054},
doi = {10.3390/mi15081054}
}
EUVIMED