EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Grayscale Lithography for the Fabrication of Flat Diffractive Infrared Lenses on Silicon Wafers

Angelos Bouchouri iD, Muhammad Nadeem Akram, Per Alfred Øhlckers iD, Xuyuan Chen iD

Micromachines · 30.06.2024 · 15 (7) · 866

DOI: 10.3390/mi15070866 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 30.06.2024. Verfasst von Angelos Bouchouri und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Microsystems, University of South-Eastern Norway, Raveien 205, 3184 Borre, Norway. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Research Council of Norway, the Norwegian Micro and Nano Fabrication Facility, Norwegian Micro- and Nano-Fabrication Facility.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Grayscale lithography (GSL) is an alternative approach to the standard binary lithography in MEMS fabrication, enabling the fabrication of complicated, arbitrary 3D structures on a wafer without the need for multiple masks and exposure steps. Despite its advantages, GSL’s effectiveness is highly dependent on controlled lab conditions, equipment consistency, and finely tuned photoresist (PR) exposure and etching processes. This works presents a thorough investigation of the challenges of GSL for silicon (Si) wafers and presents a detailed approach on how to minimize fabrication inaccuracies, aiming to replicate the intended design as closely as possible. Utilizing a maskless laser writer, all aspects of the GSL are analyzed, from photoresist exposure parameters to Si etching conditions. A practical application of GSL is demonstrated in the fabrication of 4-μm-deep f#/1 Si Fresnel lenses for long-wave infrared (LWIR) imaging (8–12 μm). The surface topography of a Fresnel lens is a good case to apply GSL, as it has varying shapes and size features that need to be preserved. The final fabricated lens profiles show a good match with the initial design, and demonstrate successful etching of coarse and fine features, and demonstrative images taken with an LWIR camera.

Schlagwörter

Stichwörter der Autor:innen

Fresnel lensMEMSgrayscalegrayscale etchinginfrared visionmultilevel

Autor:innen und Institutionen

  • Department of Microsystems, University of South-Eastern Norway, Raveien 205, 3184 Borre, Norway.

ORCID-Profile: Angelos Bouchouri, Per Alfred Øhlckers, Xuyuan Chen

Förderung

  • Research Council of Norway
  • the Norwegian Micro and Nano Fabrication Facility
  • Norwegian Micro- and Nano-Fabrication Facility

Zitieren

APA

Bouchouri, A., Akram, M. N., Øhlckers, P. A., & Chen, X. (2024). Optimization of Grayscale Lithography for the Fabrication of Flat Diffractive Infrared Lenses on Silicon Wafers. Micromachines, 15(7), 866. https://doi.org/10.3390/mi15070866

Vancouver

Bouchouri A, Akram MN, Øhlckers PA, Chen X. Optimization of Grayscale Lithography for the Fabrication of Flat Diffractive Infrared Lenses on Silicon Wafers. Micromachines. 2024;15(7):866. doi:10.3390/mi15070866

BibTeX
@article{Bouchouri2024,
  author = {Bouchouri, Angelos and Akram, Muhammad Nadeem and Øhlckers, Per Alfred and Chen, Xuyuan},
  title = {Optimization of Grayscale Lithography for the Fabrication of Flat Diffractive Infrared Lenses on Silicon Wafers},
  journal = {Micromachines},
  year = {2024},
  volume = {15},
  number = {7},
  pages = {866},
  doi = {10.3390/mi15070866}
}
Kostenlos starten →