EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on the Particle Deposition Characteristics of Transpiration Cooling Structures with Sintered Wire Mesh

Zhe Zhang iD, Xiang Luo, Yubo Peng

Micromachines · 28.03.2024 · 15 (4) · 452

DOI: 10.3390/mi15040452 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 28.03.2024. Verfasst von Zhe Zhang und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Energy and Power Engineering, Beihang University, Beijing 100191, China. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Transpiration cooling based on a porous structure has an ultra-high cooling efficiency, which is expected to be one solution to improve the cooling technology of aero-engine turbine blades. However, particulate impurities in the gas flow channel continue to deposit on the surface of turbine components, blocking cooling holes, which causes great harm to the cooling of turbine blades. In this study, a sintered metal mesh plate was selected as the transpiration cooling structure, and the evolution of particle deposition quality and deposition thickness on the transpiration cooling surface with time, as well as spatial distributions of particle deposition thickness at different times, were explored through experimental and simulation methods. The results showed that, with the increase in spray time, deposition quality and maximum deposition thickness of the transpiration cooling surface gradually increased. Along the main-stream direction, when spray time was short, deposition thickness was higher in a narrow range upstream of the experimental specimen. With the increase in spray time, deposition thickness gradually decreased along the direction of the transpiration cooling mainstream. In the spanwise direction, when spray time was very short, deposition thickness in the spanwise direction was more consistent and, after spray time increased further, the deposition thickness distribution began to tend to a “∩”-type distribution. It can be seen from the simulation results of the metal wire mesh particle deposition that particles were easily deposited on the windward side of the metal wire in the main-stream direction, which agreed with the experimental distribution characteristics of the metal wire mesh deposition. Moreover, the increase in blowing ratio reduced the deposition of particles on the wall of the metal wire mesh.

Schlagwörter

Stichwörter der Autor:innen

particle depositionsintered woven wire mesh structurespatial distribution lawtime evolution lawtranspiration cooling

Autor:innen und Institutionen

  • School of Energy and Power Engineering, Beihang University, Beijing 100191, China.
  • Research Institute of Aero-Engine, Beihang University, Beijing 100191, China.

ORCID-Profile: Zhe Zhang

Zitieren

APA

Zhang, Z., Luo, X., & Peng, Y. (2024). Study on the Particle Deposition Characteristics of Transpiration Cooling Structures with Sintered Wire Mesh. Micromachines, 15(4), 452. https://doi.org/10.3390/mi15040452

Vancouver

Zhang Z, Luo X, Peng Y. Study on the Particle Deposition Characteristics of Transpiration Cooling Structures with Sintered Wire Mesh. Micromachines. 2024;15(4):452. doi:10.3390/mi15040452

BibTeX
@article{Zhang2024,
  author = {Zhang, Zhe and Luo, Xiang and Peng, Yubo},
  title = {Study on the Particle Deposition Characteristics of Transpiration Cooling Structures with Sintered Wire Mesh},
  journal = {Micromachines},
  year = {2024},
  volume = {15},
  number = {4},
  pages = {452},
  doi = {10.3390/mi15040452}
}
Kostenlos starten →