EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface Roughness of Interior Fine Flow Channels in Selective Laser Melted Ti-6Al-4V Alloy Components

Shamoon Al Islam iD, Liang Hao iD, Zunaira Javaid, Wei Xiong, Yan Li iD, Yasir Jamil iD, Qiaoyu Chen, Guangchao Han iD

Micromachines · 29.02.2024 · 15 (3) · 348

DOI: 10.3390/mi15030348 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 29.02.2024. Verfasst von Shamoon Al Islam und 7 weiteren Autor:innen. Beteiligte Einrichtung: Gemmological Institute, China University of Geosciences, Wuhan 430074, China. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 97 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NATIONAL KEY RESEARCH AND DEVELOPMENT PROGRAM, SCIENCE AND TECHNOLOGY REVEAL SYSTEM PROJECT OF HUBEI PROVINCE, KEY RESEARCH AND DEVELOPMENT PROGRAM FUND OF HUBEI PROVINCE.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A challenge remains in achieving adequate surface roughness of SLM fabricated interior channels, which is crucial for fuel delivery in the space industry. This study investigated the surface roughness of interior fine flow channels (1 mm diameter) embedded in SLM fabricated TC4 alloy space components. A machine learning approach identified layer thickness as a significant factor affecting interior channel surface roughness, with an importance score of 1.184, followed by scan speed and laser power with scores of 0.758 and 0.512, respectively. The roughness resulted from thin layer thickness of 20 µm, predominantly formed through powder adherence, while from thicker layer of 50 µm, the roughness was mainly due to the stair step effect. Slow scan speeds increased melt pools solidification time at roof overhangs, causing molten metal to sag under gravity. Higher laser power increased melt pools temperature and led to dross formation at roof overhangs. Smaller hatch spaces increased roughness due to overlapping of melt tracks, while larger hatch spaces reduced surface roughness but led to decreased part density. The surface roughness was recorded at 34 µm for roof areas and 26.15 µm for floor areas. These findings contribute to potential adoption of TC4 alloy components in the space industry.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingbuild orientationconfined geometryheat penetrationinterior channellaser powder bed fusionoverhangprocess parameters optimizationspace industrytrapped powder

Autor:innen und Institutionen

  • Gemmological Institute, China University of Geosciences, Wuhan 430074, China.
  • Advanced Manufacturing Research Institute, China University of Geosciences, Wuhan 430074, China.
  • Hubei Jewelry Engineering Technology Research Centre, Wuhan 430074, China.
  • School of Mechanical Engineering and Electronic Information, China University of Geosciences, Wuhan 430074, China.
  • Laser Spectroscopy Laboratory, Department of Physics, University of Agriculture, Faisalabad 38040, Pakistan.

ORCID-Profile: Shamoon Al Islam, Liang Hao, Yan Li, Yasir Jamil, Guangchao Han

Förderung

  • NATIONAL KEY RESEARCH AND DEVELOPMENT PROGRAM
  • SCIENCE AND TECHNOLOGY REVEAL SYSTEM PROJECT OF HUBEI PROVINCE
  • KEY RESEARCH AND DEVELOPMENT PROGRAM FUND OF HUBEI PROVINCE
  • JOINT FUND INNOVATION TEAM PROJECT OF MINISTRY OF EDUCATION FOR EQUIPMENT PRERESEARCH
  • STATE KEY LABORATORY OF SOLIDIFICATION PROCESSING IN NPU

Zitieren

APA

Islam, S. A., Hao, L., Javaid, Z., Xiong, W., Li, Y., Jamil, Y., Chen, Q., & Han, G. (2024). Surface Roughness of Interior Fine Flow Channels in Selective Laser Melted Ti-6Al-4V Alloy Components. Micromachines, 15(3), 348. https://doi.org/10.3390/mi15030348

Vancouver

Islam SA, Hao L, Javaid Z, Xiong W, Li Y, Jamil Y, et al. Surface Roughness of Interior Fine Flow Channels in Selective Laser Melted Ti-6Al-4V Alloy Components. Micromachines. 2024;15(3):348. doi:10.3390/mi15030348

BibTeX
@article{Islam2024,
  author = {Islam, Shamoon Al and Hao, Liang and Javaid, Zunaira and Xiong, Wei and Li, Yan and Jamil, Yasir and Chen, Qiaoyu and Han, Guangchao},
  title = {Surface Roughness of Interior Fine Flow Channels in Selective Laser Melted Ti-6Al-4V Alloy Components},
  journal = {Micromachines},
  year = {2024},
  volume = {15},
  number = {3},
  pages = {348},
  doi = {10.3390/mi15030348}
}
Kostenlos starten →