EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Printability, Microstructure, and Mechanical Properties of Fe80−xMnxCo10Cr10 High-Entropy Alloys Fabricated by Laser Powder Bed Fusion Additive Manufacturing

Kai Li, Vyacheslav Trofimov iD, Changjun Han iD, Gaoling Hu, Zhi Dong, Yujin Zou, Zaichi Wang, Fubao Yan, Zhiqiang Fu, Yongqiang Yang

Micromachines · 11.01.2024 · 15 (1) · 123

DOI: 10.3390/mi15010123 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 11.01.2024. Verfasst von Kai Li und 9 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510641, China. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Fundamental Research Funds for the Central Universities, Guangdong Basic and Applied Basic Research Foundation, Science and Technology Program of Guangzhou.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work investigated the effect of Fe/Mn ratio on the microstructure and mechanical properties of non-equimolar Fe80−xMnxCo10Cr10 (x = 30% and 50%) high-entropy alloys (HEAs) fabricated by laser powder bed fusion (LPBF) additive manufacturing. Process optimization was conducted to achieve fully dense Fe30Mn50Co10Cr10 and Fe50Mn30Co10Cr10 HEAs using a volumetric energy density of 105.82 J·mm−3. The LPBF-printed Fe30Mn50Co10Cr10 HEA exhibited a single face-centered cubic (FCC) phase, while the Fe50Mn30Co10Cr10 HEA featured a hexagonal close-packed (HCP) phase within the FCC matrix. Notably, the fraction of HCP phase in the Fe50Mn30Co10Cr10 HEAs increased from 0.94 to 28.10%, with the deformation strain ranging from 0 to 20%. The single-phase Fe30Mn50Co10Cr10 HEA demonstrated a remarkable combination of high yield strength (580.65 MPa) and elongation (32.5%), which surpassed those achieved in the FeMnCoCr HEA system. Comparatively, the dual-phase Fe50Mn30Co10Cr10 HEA exhibited inferior yield strength (487.60 MPa) and elongation (22.3%). However, it displayed superior ultimate tensile strength (744.90 MPa) compared to that in the Fe30Mn50Co10Cr10 HEA (687.70 MPa). The presence of FCC/HCP interfaces obtained in the Fe50Mn30Co10Cr10 HEA resulted in stress concentration and crack expansion, thereby leading to reduced ductility but enhanced resistance against grain slip deformation. Consequently, these interfaces facilitated an earlier attainment of yield limit point and contributed to increased ultimate tensile strength in the Fe50Mn30Co10Cr10 HEA. These findings provide valuable insights into the microstructure evolution and mechanical behavior of LPBF-printed metastable FeMnCoCr HEAs.

Schlagwörter

Stichwörter der Autor:innen

FeMnCoCradditive manufacturinghigh-entropy alloyslaser powder bed fusiontransformation-induced plasticity

Autor:innen und Institutionen

  • School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510641, China.

ORCID-Profile: Vyacheslav Trofimov, Changjun Han

Förderung

  • the Fundamental Research Funds for the Central Universities
  • Guangdong Basic and Applied Basic Research Foundation
  • Science and Technology Program of Guangzhou
  • Fundamental Research Funds for the Central Universities

Zitieren

APA

Li, K., Trofimov, V., Han, C., Hu, G., Dong, Z., Zou, Y., Wang, Z., Yan, F., Fu, Z., & Yang, Y. (2024). The Printability, Microstructure, and Mechanical Properties of Fe80−xMnxCo10Cr10 High-Entropy Alloys Fabricated by Laser Powder Bed Fusion Additive Manufacturing. Micromachines, 15(1), 123. https://doi.org/10.3390/mi15010123

Vancouver

Li K, Trofimov V, Han C, Hu G, Dong Z, Zou Y, et al. The Printability, Microstructure, and Mechanical Properties of Fe80−xMnxCo10Cr10 High-Entropy Alloys Fabricated by Laser Powder Bed Fusion Additive Manufacturing. Micromachines. 2024;15(1):123. doi:10.3390/mi15010123

BibTeX
@article{Li2024,
  author = {Li, Kai and Trofimov, Vyacheslav and Han, Changjun and Hu, Gaoling and Dong, Zhi and Zou, Yujin and Wang, Zaichi and Yan, Fubao and Fu, Zhiqiang and Yang, Yongqiang},
  title = {The Printability, Microstructure, and Mechanical Properties of Fe80−xMnxCo10Cr10 High-Entropy Alloys Fabricated by Laser Powder Bed Fusion Additive Manufacturing},
  journal = {Micromachines},
  year = {2024},
  volume = {15},
  number = {1},
  pages = {123},
  doi = {10.3390/mi15010123}
}
Kostenlos starten →