EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Investigations of Using Aluminum Oxide (Al2O3) and Nano-Graphene Powder in the Electrical Discharge Machining of Titanium Alloy

Rakesh Chaudhari iD, Sakshum Khanna iD, Vivek K Patel iD, Jay Vora iD, Soraya Plaza, Luis Norberto López de Lacalle iD

Micromachines · 16.12.2023 · 14 (12) · 2247

DOI: 10.3390/mi14122247 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 16.12.2023. Verfasst von Rakesh Chaudhari und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, School of Technology, Pandit Deendayal Energy University, Gandhinagar 382007, India. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 70 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Basque government through University research groups.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present study, a comprehensive parametric analysis was carried out using the electrical discharge machining of Ti6Al4V, using pulse-on time, current, and pulse-off time as input factors with output measures of surface roughness and material removal rate. The present study also used two different nanopowders, namely alumina and nano-graphene, to analyze their effect on output measures and surface defects. All the experimental runs were performed using Taguchi’s array at three levels. Analysis of variance was employed to study the statistical significance. Empirical relations were generated through Minitab. The regression model term was observed to be significant for both the output responses, which suggested that the generated regressions were adequate. Among the input factors, pulse-off time and current were found to have a vital role in the change in material removal rate, while pulse-on time was observed as a vital input parameter. For surface quality, pulse-on time and pulse-off time were recognized to be influential parameters, while current was observed to be an insignificant factor. Teaching–learning-based optimization was used for the optimization of output responses. The influence of alumina and nano-graphene powder was investigated at optimal process parameters. The machining performance was significantly improved by using both powder-mixed electrical discharge machining as compared to the conventional method. Due to the higher conductivity of nano-graphene powder, it showed a larger improvement as compared to alumina powder. Lastly, scanning electron microscopy was operated to investigate the impact of alumina and graphene powder on surface morphology. The machined surface obtained for the conventional process depicted more surface defects than the powder-mixed process, which is key in aeronautical applications.

Schlagwörter

Stichwörter der Autor:innen

EDMTLBO algorithmTi6Al4Valuminum oxide (Al2O3) nanopowdernano-graphene

Autor:innen und Institutionen

  • Department of Mechanical Engineering, School of Technology, Pandit Deendayal Energy University, Gandhinagar 382007, India.
  • School of Technology, Pandit Deendayal Energy University, Gandhinagar 382007, India.
  • Department of Mechanical Engineering, University of the Basque Country, Escuela Superior de Ingenieros Alameda de Urquijo s/n, 48013 Bilbao, Spain.

ORCID-Profile: Rakesh Chaudhari, Sakshum Khanna, Vivek K Patel, Jay Vora, Luis Norberto López de Lacalle

Förderung

  • Basque government through University research groups

Zitieren

APA

Chaudhari, R., Khanna, S., Patel, V. K., Vora, J., Plaza, S., & Lacalle, L. N. L. (2023). Experimental Investigations of Using Aluminum Oxide (Al2O3) and Nano-Graphene Powder in the Electrical Discharge Machining of Titanium Alloy. Micromachines, 14(12), 2247. https://doi.org/10.3390/mi14122247

Vancouver

Chaudhari R, Khanna S, Patel VK, Vora J, Plaza S, Lacalle LNL. Experimental Investigations of Using Aluminum Oxide (Al2O3) and Nano-Graphene Powder in the Electrical Discharge Machining of Titanium Alloy. Micromachines. 2023;14(12):2247. doi:10.3390/mi14122247

BibTeX
@article{Chaudhari2023,
  author = {Chaudhari, Rakesh and Khanna, Sakshum and Patel, Vivek K and Vora, Jay and Plaza, Soraya and Lacalle, Luis Norberto López de},
  title = {Experimental Investigations of Using Aluminum Oxide (Al2O3) and Nano-Graphene Powder in the Electrical Discharge Machining of Titanium Alloy},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {12},
  pages = {2247},
  doi = {10.3390/mi14122247}
}
Kostenlos starten →