EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of Machining Characteristics in Electrical Discharge Machining Using a Slotted Electrode with Internal Flushing

Minghao Gao, Ming Liu, Jianqing Han, Qinhe Zhang

Micromachines · 27.10.2023 · 14 (11) · 1989

DOI: 10.3390/mi14111989 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 27.10.2023. Verfasst von Minghao Gao und 3 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory of High Efficiency and Clean Mechanical Manufacture (Ministry of Education), School of Mechanical Engineering, Shandong University, Ji…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In die-sinking electrical discharge machining (EDM), it is challenging to implement internal flushing, mainly because it is easy to produce residual material columns on the workpiece cavity’s bottom surface, affecting the processing quality and efficiency. In order to solve this problem, the internal flushing slotted electrode EDM technology was proposed. The slotted electrode was designed, and its preparation method was described. The influence of pulse width, pulse interval, and flushing pressure on the performance of the internal flushing slotted electrode EDM was studied using single-factor experiments. The experimental results indicate that, with the increase in pulse width, the material removal rate (MRR) increases first and then decreases, while the electrode wear rate (EWR) and the relative electrode wear rate (REWR) decrease gradually; with the increase in pulse interval, the MRR decreases, while the EWR and the REWR increase gradually; with the increase in flushing pressure, the MRR increases first and then decreases, while the EWR and the REWR increase gradually. When the slotted electrode is used for continuous internal flushing EDM, the appropriate pulse width, flushing pressure, and smaller pulse interval can improve the MRR and reduce the EWR and the REWR.

Schlagwörter

Stichwörter der Autor:innen

electrical discharge machininginternal flushingmachining characteristicsslotted electrode

Autor:innen und Institutionen

  • Key Laboratory of High Efficiency and Clean Mechanical Manufacture (Ministry of Education), School of Mechanical Engineering, Shandong University, Jinan 250061, China.
  • National Demonstration Center for Experimental Mechanical Engineering Education, Shandong University, Jinan 250061, China.

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Gao, M., Liu, M., Han, J., & Zhang, Q. (2023). Investigation of Machining Characteristics in Electrical Discharge Machining Using a Slotted Electrode with Internal Flushing. Micromachines, 14(11), 1989. https://doi.org/10.3390/mi14111989

Vancouver

Gao M, Liu M, Han J, Zhang Q. Investigation of Machining Characteristics in Electrical Discharge Machining Using a Slotted Electrode with Internal Flushing. Micromachines. 2023;14(11):1989. doi:10.3390/mi14111989

BibTeX
@article{Gao2023,
  author = {Gao, Minghao and Liu, Ming and Han, Jianqing and Zhang, Qinhe},
  title = {Investigation of Machining Characteristics in Electrical Discharge Machining Using a Slotted Electrode with Internal Flushing},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {11},
  pages = {1989},
  doi = {10.3390/mi14111989}
}
Kostenlos starten →