EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fabrication of µFFE Devices in COC via Hot Embossing with a 3D-Printed Master Mold

Matthew B LeMon, Cecilia C Douma iD, Gretchen S Burke iD, Michael T Bowser iD

Micromachines · 02.09.2023 · 14 (9) · 1728

DOI: 10.3390/mi14091728 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 02.09.2023. Verfasst von Matthew B LeMon und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, University of Minnesota, Minneapolis, MN 55455, USA. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NIDDK NIH HHS, NIGMS NIH HHS, National Institutes of Health.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The fabrication of high-performance microscale devices in substrates with optimal material properties while keeping costs low and maintaining the flexibility to rapidly prototype new designs remains an ongoing challenge in the microfluidics field. To this end, we have fabricated a micro free-flow electrophoresis (µFFE) device in cyclic olefin copolymer (COC) via hot embossing using a PolyJet 3D-printed master mold. A room-temperature cyclohexane vapor bath was used to clarify the device and facilitate solvent-assisted thermal bonding to fully enclose the channels. Device profiling showed 55 µm deep channels with no detectable feature degradation due to solvent exposure. Baseline separation of fluorescein, rhodamine 110, and rhodamine 123, was achieved at 150 V. Limits of detection for these fluorophores were 2 nM, 1 nM, and 10 nM, respectively, and were comparable to previously reported values for glass and 3D-printed devices. Using PolyJet 3D printing in conjunction with hot embossing, the full design cycle, from initial design to production of fully functional COC µFFE devices, could be completed in as little as 6 days without the need for specialized clean room facilities. Replicate COC µFFE devices could be produced from an existing embossing mold in as little as two hours.

Schlagwörter

Stichwörter der Autor:innen

3D printingcyclic olefin copolymerhot embossingmicro free-flow electrophoresismicrofluidics

Autor:innen und Institutionen

  • Department of Chemistry, University of Minnesota, Minneapolis, MN 55455, USA.

ORCID-Profile: Cecilia C Douma, Gretchen S Burke, Michael T Bowser

Förderung

  • NIDDK NIH HHS
  • NIGMS NIH HHS
  • National Institutes of Health

Zitieren

APA

LeMon, M. B., Douma, C. C., Burke, G. S., & Bowser, M. T. (2023). Fabrication of µFFE Devices in COC via Hot Embossing with a 3D-Printed Master Mold. Micromachines, 14(9), 1728. https://doi.org/10.3390/mi14091728

Vancouver

LeMon MB, Douma CC, Burke GS, Bowser MT. Fabrication of µFFE Devices in COC via Hot Embossing with a 3D-Printed Master Mold. Micromachines. 2023;14(9):1728. doi:10.3390/mi14091728

BibTeX
@article{LeMon2023,
  author = {LeMon, Matthew B and Douma, Cecilia C and Burke, Gretchen S and Bowser, Michael T},
  title = {Fabrication of µFFE Devices in COC via Hot Embossing with a 3D-Printed Master Mold},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {9},
  pages = {1728},
  doi = {10.3390/mi14091728}
}
Kostenlos starten →