EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Cu-Cu Thermocompression Bonding with a Self-Assembled Monolayer as Oxidation Protection for 3D/2.5D System Integration

Maria Lykova, Iuliana Panchenko, Martin Schneider-Ramelow, Tadatomo Suga iD, Fengwen Mu, Roy Buschbeck

Micromachines · 30.06.2023 · 14 (7) · 1365

DOI: 10.3390/mi14071365 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 30.06.2023. Verfasst von Maria Lykova und 5 weiteren Autor:innen. Beteiligte Einrichtung: Fraunhofer Institute for Electronic Nanosystems ENAS, 09126 Chemnitz, Germany. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: TU Dresden Graduate Academy, Graduate Academy.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Cu-Cu direct interconnects are highly desirable for the microelectronic industry as they allow for significant reductions in the size and spacing of microcontacts. The main challenge associated with using Cu is its tendency to rapidly oxidize in air. This research paper describes a method of Cu passivation using a self-assembled monolayer (SAM) to protect the surface against oxidation. However, this approach faces two main challenges: the degradation of the SAM at room temperature in the ambient atmosphere and the monolayer desorption technique prior to Cu-Cu bonding. In this paper, the systematic investigation of these challenges and their possible solutions are presented. The methods used in this study include thermocompression (TC) bonding, X-ray photoelectron spectroscopy (XPS), shear strength testing, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The results indicate nearly no Cu oxidation (4 at.%) for samples with SAM passivation in contrast to the bare Cu surface (27 at.%) after the storage at −18 °C in a conventional freezer for three weeks. Significant improvement was observed in the TC bonding with SAM after storage. The mean shear strength of the passivated samples reached 65.5 MPa without storage. The average shear strength values before and after the storage tests were 43% greater for samples with SAM than for the bare Cu surface. In conclusion, this study shows that Cu-Cu bonding technology can be improved by using SAM as an oxidation inhibitor, leading to a higher interconnect quality.

Schlagwörter

Stichwörter der Autor:innen

Cu-Cu bondingSAMSAM desorptionself-assembled monolayersthermocompression bonding

Autor:innen und Institutionen

  • Fraunhofer Institute for Electronic Nanosystems ENAS, 09126 Chemnitz, Germany.
  • Institute of Electronic Packaging Technology (IAVT), TU Dresden, 01062 Dresden, Germany.
  • All Silicon System Integration Dresden (ASSID), Fraunhofer Institute for Reliability and Microintegration (IZM), 01468 Dresden, Germany.
  • Fraunhofer Institute for Reliability and Microintegration (IZM), 13355 Berlin, Germany.
  • Collaborative Research Center, Meisei University, Tokyo 191-8506, Japan.
  • Department of Precision Engineering, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656, Japan.

ORCID-Profile: Tadatomo Suga

Förderung

  • TU Dresden Graduate Academy
  • Graduate Academy

Zitieren

APA

Lykova, M., Panchenko, I., Schneider-Ramelow, M., Suga, T., Mu, F., & Buschbeck, R. (2023). Cu-Cu Thermocompression Bonding with a Self-Assembled Monolayer as Oxidation Protection for 3D/2.5D System Integration. Micromachines, 14(7), 1365. https://doi.org/10.3390/mi14071365

Vancouver

Lykova M, Panchenko I, Schneider-Ramelow M, Suga T, Mu F, Buschbeck R. Cu-Cu Thermocompression Bonding with a Self-Assembled Monolayer as Oxidation Protection for 3D/2.5D System Integration. Micromachines. 2023;14(7):1365. doi:10.3390/mi14071365

BibTeX
@article{Lykova2023,
  author = {Lykova, Maria and Panchenko, Iuliana and Schneider-Ramelow, Martin and Suga, Tadatomo and Mu, Fengwen and Buschbeck, Roy},
  title = {Cu-Cu Thermocompression Bonding with a Self-Assembled Monolayer as Oxidation Protection for 3D/2.5D System Integration},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {7},
  pages = {1365},
  doi = {10.3390/mi14071365}
}
Kostenlos starten →