EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Simulation-Assisted Process Design and Experimental Verification of Laterally Confined Oxide Areas Generated with Continuous Electrolytic Free Jet on EN AW-7075 Aluminum Alloy

Susanne Quitzke iD, Igor Danilov, André Martin iD, Roy Morgenstern, Thomas Lampke iD, Andreas Schubert iD

Micromachines · 22.01.2023 · 14 (2) · 293

DOI: 10.3390/mi14020293 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 22.01.2023. Verfasst von Susanne Quitzke und 5 weiteren Autor:innen. Beteiligte Einrichtung: Professorship Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz, Germany. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Local anodization with a free electrolyte jet is a suitable solution for locally confined surface functionalization without additionally required preparation of the parts. However, the geometrical formation of the anodic oxide layer in jet-based anodization is not yet sufficiently understood. In this study, numerical calculations based on physical descriptions are used to describe the lateral and vertical oxide formation on aluminum alloy EN AW-7075. The required electrical resistance and capacitance were determined by immersion-based anodization and implemented into the numerical simulation model to evaluate the electrical conductivity of the porous layer. The simulation results showed an electrical conductivity of 2.6 × 10−6 S/m for the porous layer. Subsequently, a model for jet-based anodization was developed and the previous results were implemented to calculate the oxide formation. The simulation results showed decreasing oxide layer thickness at increasing radial distance from the center of the jet, which corresponds to experimental results. The simulation model was validated by varying the current efficiency from 5% to 90%, where similar developments of the anodic oxide layer thickness compared with experimental results were determined at 5%.

Schlagwörter

Stichwörter der Autor:innen

electrodynamic simulationfree electrolyte jetlocal functionalizationlocalized mask-less anodizationoxide layer formation

Autor:innen und Institutionen

  • Professorship Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz, Germany.
  • Materials and Surface Engineering, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz, Germany.

ORCID-Profile: Susanne Quitzke, André Martin, Thomas Lampke, Andreas Schubert

Förderung

  • Deutsche Forschungsgemeinschaft

Zitieren

APA

Quitzke, S., Danilov, I., Martin, A., Morgenstern, R., Lampke, T., & Schubert, A. (2023). Simulation-Assisted Process Design and Experimental Verification of Laterally Confined Oxide Areas Generated with Continuous Electrolytic Free Jet on EN AW-7075 Aluminum Alloy. Micromachines, 14(2), 293. https://doi.org/10.3390/mi14020293

Vancouver

Quitzke S, Danilov I, Martin A, Morgenstern R, Lampke T, Schubert A. Simulation-Assisted Process Design and Experimental Verification of Laterally Confined Oxide Areas Generated with Continuous Electrolytic Free Jet on EN AW-7075 Aluminum Alloy. Micromachines. 2023;14(2):293. doi:10.3390/mi14020293

BibTeX
@article{Quitzke2023,
  author = {Quitzke, Susanne and Danilov, Igor and Martin, André and Morgenstern, Roy and Lampke, Thomas and Schubert, Andreas},
  title = {Simulation-Assisted Process Design and Experimental Verification of Laterally Confined Oxide Areas Generated with Continuous Electrolytic Free Jet on EN AW-7075 Aluminum Alloy},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {2},
  pages = {293},
  doi = {10.3390/mi14020293}
}
Kostenlos starten →