EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Precursor Alloy Overheating on Controlled Diffusion Solidification of Mg-Al-Zn Alloys

Xinyi Zhao, Shanguang Liu, Tao Gu, Yang Sun, Hong Qin, Dan Wang, Peizhong Feng

Metals · 21.07.2026 · 16 (7) · 819

DOI: 10.3390/met16070819 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 21.07.2026. Verfasst von Xinyi Zhao und 6 weiteren Autor:innen. Die Arbeit nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Diffusion solidification is an effective method to produce non-dendritic microstructures and reduce casting defects in magnesium alloys. However, the influence of precursor alloy superheat on the solidification behavior and the resulting microstructure remains insufficiently understood. In this study, pure magnesium was used as the high thermal mass (HTM) alloy and three Mg-Al-Zn alloys with different aluminum and zinc contents were used as the low thermal mass (LTM) alloys. The effects of superheat on grain morphology, solute diffusion, and constitutional supercooling were investigated through a combination of experimental casting and numerical simulation using Ansys Fluent and Matlab. The results show that the solidified interface consists of five distinct regions, including two base metals, two transition zones, and a central controlled diffusion solidification zone. A higher superheat of the HTM alloy relative to the LTM alloy promotes a wider transition zone and finer globular grains, whereas equal or lower superheat leads to columnar or rosette structures. The Mg-30 wt.%Al-3.5 wt.%Zn alloy with moderate aluminum content produces fine globular grains due to a thinner constitutional supercooling layer and a higher degree of supercooling, which suppresses grain growth and increases nucleation rate. In contrast, the Mg-55 wt.%Al-6.5 wt.%Zn alloy with high aluminum content forms coarse rosette and columnar grains. Among the conditions investigated, the combination of 10 °C HTM and 5 °C LTM superheats tends to promote the formation of fine equiaxed grains. Increasing superheat above this range reduces supercooling and coarsens grains, while decreasing superheat inhibits interface diffusion and promotes solute segregation. The findings provide a theoretical basis for designing precursor alloy compositions and superheat parameters in controlled diffusion solidification of magnesium alloys.

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Zhao, X., Liu, S., Gu, T., Sun, Y., Qin, H., Wang, D., & Feng, P. (2026). Effect of Precursor Alloy Overheating on Controlled Diffusion Solidification of Mg-Al-Zn Alloys. Metals, 16(7), 819. https://doi.org/10.3390/met16070819

Vancouver

Zhao X, Liu S, Gu T, Sun Y, Qin H, Wang D, et al. Effect of Precursor Alloy Overheating on Controlled Diffusion Solidification of Mg-Al-Zn Alloys. Metals. 2026;16(7):819. doi:10.3390/met16070819

BibTeX
@article{Zhao2026,
  author = {Zhao, Xinyi and Liu, Shanguang and Gu, Tao and Sun, Yang and Qin, Hong and Wang, Dan and Feng, Peizhong},
  title = {Effect of Precursor Alloy Overheating on Controlled Diffusion Solidification of Mg-Al-Zn Alloys},
  journal = {Metals},
  year = {2026},
  volume = {16},
  number = {7},
  pages = {819},
  doi = {10.3390/met16070819}
}
Kostenlos starten →