Effects of Hot Compression Parameters on Flow Behavior and Microstructural Evolution of 7050 Aluminum Alloy
Metals · 03.07.2026 · 16 (7) · 733
DOI: 10.3390/met16070733 ↗Kurz gefasst
Fachartikel in der Zeitschrift Metals, online erschienen am 03.07.2026. Verfasst von Liang Xu und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: State Key Laboratory of Precision Manufacturing for Extreme Service Performance, Central South University, Key Research and Development Program of Shandong Province.
Abstract (Originalsprache)
The hot deformation behavior of 7050 aluminum alloy was investigated by isothermal compression tests over a temperature range of 250 °C to 450 °C and a strain-rate range of 0.001 s−1 to 1 s−1. The flow stress was strongly dependent on both temperature and strain rate. At a strain rate of 0.1 s−1, increasing the temperature from 250 °C to 450 °C reduced the peak stress by 72.7%. At 450 °C, decreasing the strain rate from 1 s−1 to 0.001 s−1 reduced the peak stress from 66.7 MPa to 14.6 MPa, corresponding to a decrease of 78.1%. Based on the peak stress, an Arrhenius-type constitutive equation was established, with a deformation activation energy of 179.35 kJ mol−1. The predicted peak stresses agree well with the experimental values, giving a correlation coefficient (R2) of 0.98. The processing map indicates that the optimal hot working domain is located at 400–450 °C and 0.001–0.05 s−1. Scanning electron microscopy (SEM) observations showed that increasing temperature promoted the reduction in second-phase particles, with their area fraction decreasing from 5.3% at 250 °C to 1.2% at 450 °C under 0.001 s−1. In comparison, strain rate had a smaller effect on the particle area fraction at 450 °C. Electron backscatter diffraction (EBSD) analysis revealed that high temperature and low strain rate enhanced dynamic recovery and grain-boundary misorientation evolution. The fraction of low-angle grain boundaries (LAGBs) decreased from 71.5% to 38.8% as the temperature increased from 250 °C to 450 °C under 0.001 s−1, and decreased from 48.2% to 38.8% when the strain rate decreased from 1 s−1 to 0.001 s−1 at 450 °C.
Förderung
- State Key Laboratory of Precision Manufacturing for Extreme Service Performance, Central South University
- Key Research and Development Program of Shandong Province
Zitieren
APA
Xu, L., Yi, Y., Huang, S., He, H., Wang, W., & Dong, F. (2026). Effects of Hot Compression Parameters on Flow Behavior and Microstructural Evolution of 7050 Aluminum Alloy. Metals, 16(7), 733. https://doi.org/10.3390/met16070733
Vancouver
Xu L, Yi Y, Huang S, He H, Wang W, Dong F. Effects of Hot Compression Parameters on Flow Behavior and Microstructural Evolution of 7050 Aluminum Alloy. Metals. 2026;16(7):733. doi:10.3390/met16070733
BibTeX
@article{Xu2026,
author = {Xu, Liang and Yi, Youping and Huang, Shiquan and He, Hailin and Wang, Wenke and Dong, Fei},
title = {Effects of Hot Compression Parameters on Flow Behavior and Microstructural Evolution of 7050 Aluminum Alloy},
journal = {Metals},
year = {2026},
volume = {16},
number = {7},
pages = {733},
doi = {10.3390/met16070733}
}
EUVIMED