EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of TiC Content on the Microstructure and Wear Resistance of CoCrFeNi-TiC Composite Coatings Prepared by Laser Cladding

Weidan Liao, Xueguang Chen, Yang Yang, Kaihong Song, Yujie Wang, Shihong Ren, Nianxi Hua, Mengduo Hu, Jiaxuan Li

Metals · 02.07.2026 · 16 (7) · 728

DOI: 10.3390/met16070728 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 02.07.2026. Verfasst von Weidan Liao und 8 weiteren Autor:innen. Die Arbeit nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Hebei Province Higher Education Science and Technology Research Project.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To overcome the insufficient hardness and wear resistance of CoCrFeNi alloy coatings under heavy-load conditions, CoCrFeNi-TiC composite coatings with varying TiC mass fractions were fabricated on a 42CrMo substrate using laser cladding. The present study systematically investigates the effects of TiC content on phase composition, microstructural evolution, microhardness, and tribological behavior. The results show that TiC addition does not change the primary phase constitution of the face-centered cubic (FCC) matrix, but induces lattice distortion and grain refinement, resulting in a pronounced enhancement of coating hardness. As the TiC content increased, the average microhardness rose from 222.9 HV0.2 to 380.9 HV0.2, which was 1.7 times that of the coating without TiC. The enhanced hardness is mainly attributed to grain refinement, solid-solution strengthening, and the dispersion effects of TiC particles. The tribological performance showed a non-monotonic dependence on TiC content. Among the tested samples, the coating with 10 wt.%TiC showed the best wear resistance, with an average friction coefficient of 0.56 and a wear rate of 1.15 × 10−4 mm3/(N·m). However, further increasing the TiC content to 15 wt.% slightly reduced wear resistance because particle spalling promoted three-body abrasive wear. These results indicate that an appropriate TiC content can improve the balance between hard-phase strengthening and wear stability of CoCrFeNi-based composite coatings. This work clarifies the microstructure regulation and wear failure mechanism of TiC-reinforced coatings, providing experimental guidance for heavy-load service coating design.

Förderung

  • Hebei Province Higher Education Science and Technology Research Project

Zitieren

APA

Liao, W., Chen, X., Yang, Y., Song, K., Wang, Y., Ren, S., Hua, N., Hu, M., & Li, J. (2026). Effect of TiC Content on the Microstructure and Wear Resistance of CoCrFeNi-TiC Composite Coatings Prepared by Laser Cladding. Metals, 16(7), 728. https://doi.org/10.3390/met16070728

Vancouver

Liao W, Chen X, Yang Y, Song K, Wang Y, Ren S, et al. Effect of TiC Content on the Microstructure and Wear Resistance of CoCrFeNi-TiC Composite Coatings Prepared by Laser Cladding. Metals. 2026;16(7):728. doi:10.3390/met16070728

BibTeX
@article{Liao2026,
  author = {Liao, Weidan and Chen, Xueguang and Yang, Yang and Song, Kaihong and Wang, Yujie and Ren, Shihong and Hua, Nianxi and Hu, Mengduo and Li, Jiaxuan},
  title = {Effect of TiC Content on the Microstructure and Wear Resistance of CoCrFeNi-TiC Composite Coatings Prepared by Laser Cladding},
  journal = {Metals},
  year = {2026},
  volume = {16},
  number = {7},
  pages = {728},
  doi = {10.3390/met16070728}
}
Kostenlos starten →