EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on the Wear Resistance of Laser-Cladded CoCrFeMnNi Coatings Under Machine Hammer Peening

Rui Wang, Juan Hou, Lu Yu, Shouwei Xu, Lihong Su, Hui Wang, Xi Huang

Metals · 29.06.2026 · 16 (7) · 712

DOI: 10.3390/met16070712 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 29.06.2026. Verfasst von Rui Wang und 6 weiteren Autor:innen. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Nantong University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

CoCrFeMnNi high-entropy alloy (HEA) coatings were fabricated on an S41500 stainless steel substrate by laser cladding and subsequently strengthened using machine hammer peening (MHP) at three hammering energies of 1.7 J, 3.5 J, and 5.0 J. The effects of MHP treatment on the phase structure, surface morphology, microhardness, and tribological properties of the coatings were systematically investigated. The results showed that all coatings retained a single-phase face-centered cubic (FCC) structure after MHP treatment, indicating excellent microstructural stability during impact-induced strengthening. With increasing hammering energy, the surface morphology gradually evolved from discrete hammering indentations to a more continuous orange-peel-like texture, while the surface roughness initially increased and then decreased. MHP significantly enhanced the surface hardness of the coatings. In particular, the MHP3.5 sample exhibited the highest surface hardness of approximately 420 HV, representing an increase of about 120% compared with the untreated coating. Under dry sliding conditions at a load of 30 N, the MHP3.5 sample exhibited the lowest and most stable friction coefficient, maintaining a steady-state value of approximately 0.40–0.45. Its specific wear rate decreased by nearly 45% compared with that of the untreated coating. The improved wear resistance was mainly attributed to the combined effects of strain hardening, grain refinement, and dislocation strengthening induced by machine hammer peening. Considering the hardness, friction coefficient, and specific wear rate results together, a hammering energy of 3.5 J was identified as the most suitable MHP parameter under the low-load wear conditions investigated in this study.

Förderung

  • National Natural Science Foundation of China
  • Nantong University

Zitieren

APA

Wang, R., Hou, J., Yu, L., Xu, S., Su, L., Wang, H., & Huang, X. (2026). Study on the Wear Resistance of Laser-Cladded CoCrFeMnNi Coatings Under Machine Hammer Peening. Metals, 16(7), 712. https://doi.org/10.3390/met16070712

Vancouver

Wang R, Hou J, Yu L, Xu S, Su L, Wang H, et al. Study on the Wear Resistance of Laser-Cladded CoCrFeMnNi Coatings Under Machine Hammer Peening. Metals. 2026;16(7):712. doi:10.3390/met16070712

BibTeX
@article{Wang2026,
  author = {Wang, Rui and Hou, Juan and Yu, Lu and Xu, Shouwei and Su, Lihong and Wang, Hui and Huang, Xi},
  title = {Study on the Wear Resistance of Laser-Cladded CoCrFeMnNi Coatings Under Machine Hammer Peening},
  journal = {Metals},
  year = {2026},
  volume = {16},
  number = {7},
  pages = {712},
  doi = {10.3390/met16070712}
}
Kostenlos starten →