EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Cutting Insert Flank Wear in Previous Turning and Subsequent Diamond Burnishing on the Surface Integrity, Microstructure and Fatigue Limit of Heat-Treated C45 Steel

Jordan Maximov, Galya Duncheva, Angel Anchev, Vladimir Dunchev, Kalin Anastasov, Mariana Ichkova

Metals · 11.05.2026 · 16 (5) · 520

DOI: 10.3390/met16050520 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 11.05.2026. Verfasst von Jordan Maximov und 5 weiteren Autor:innen. Die Arbeit nennt 58 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Burnishing technologies are a cheap and effective means of improving the surface integrity (SI) and performance of metal components. However, there is practically no information about the integral influence of the preceding turning process on the initial (pre-burnishing) SI. This study answers the question of how the white layer resulting from flank wear on the cutting insert in pre-turning affects the SI and fatigue limit, and determines the extent to which subsequent diamond burnishing (DB) is able to improve the SI and rotating bending fatigue limit of normalised, quenched and high-temperature-tempered C45 steel. The (DB)–SI–fatigue limit correlation was investigated using a holistic approach that took into account the effects of the dynamic pattern of flank wear on the initial SI. An explicit relationship was established between the flank wear, the affected surface layer structure and the fatigue limit. Increasing flank wear to the 60th minute intensified the formation of a gradient layer with finer and thinner grains that formed a texture. As a result, a synergistic effect was observed from turning with an insert operating for 60 min and subsequent DB, which maximised the fatigue limit (741 MPa). After 60 min, the structure of the affected layer changed qualitatively towards the formation of a nanostructured (white) layer, which reversed the trend, worsening the fatigue behaviour. As the thickness of the white layer increased, the fatigue limit was sharply reduced to below 560 MPa after the 90th minute. Regardless of the degree of flank wear, DB significantly improved the SI characteristics and increased the fatigue limit after turning with a worn insert, although the absolute dimensions of the positive DB effect depend on the initial SI and fatigue limit due to pre-turning. To achieve a synergistic effect, the cutting insert should be replaced with a new one after every 60 min of operation.

Zitieren

APA

Maximov, J., Duncheva, G., Anchev, A., Dunchev, V., Anastasov, K., & Ichkova, M. (2026). Effects of Cutting Insert Flank Wear in Previous Turning and Subsequent Diamond Burnishing on the Surface Integrity, Microstructure and Fatigue Limit of Heat-Treated C45 Steel. Metals, 16(5), 520. https://doi.org/10.3390/met16050520

Vancouver

Maximov J, Duncheva G, Anchev A, Dunchev V, Anastasov K, Ichkova M. Effects of Cutting Insert Flank Wear in Previous Turning and Subsequent Diamond Burnishing on the Surface Integrity, Microstructure and Fatigue Limit of Heat-Treated C45 Steel. Metals. 2026;16(5):520. doi:10.3390/met16050520

BibTeX
@article{Maximov2026,
  author = {Maximov, Jordan and Duncheva, Galya and Anchev, Angel and Dunchev, Vladimir and Anastasov, Kalin and Ichkova, Mariana},
  title = {Effects of Cutting Insert Flank Wear in Previous Turning and Subsequent Diamond Burnishing on the Surface Integrity, Microstructure and Fatigue Limit of Heat-Treated C45 Steel},
  journal = {Metals},
  year = {2026},
  volume = {16},
  number = {5},
  pages = {520},
  doi = {10.3390/met16050520}
}
Kostenlos starten →