EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Hybrid Thermo-Vibrational Welding with Active Cooling for Preheat-Free Joining of Martensitic 15Kh5M Steel: Microstructural Refinement and Heat-Affected Zone Control

Airat M. Fairushin, Elena Yu. Tumanova, Andrey S. Tokarev, Natalya B. Mulyashova, Azamat S. Ilalov, Alsu R. Kanaeva, Arseny M. Kazakov, Galiia F. Korznikova

Metals · 03.05.2026 · 16 (5) · 499

DOI: 10.3390/met16050499 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 03.05.2026. Verfasst von Airat M. Fairushin und 7 weiteren Autor:innen. Die Arbeit nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Ministry of Education and Science of the Russian Federation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Martensitic chromium-molybdenum steels such as 15Kh5M are widely used in high-temperature oil and gas equipment, but their weldability is limited by high hardenability and susceptibility to cold cracking, which usually necessitate energy-intensive preheating. This study evaluates an alternative route based on the combination of root-pass mechanical vibration (50 Hz, ~1 mm amplitude) and post-pass water-air jet cooling during mechanized GMAW. Three welding variants were compared: conventional preheated welding, vibration-assisted welding without preheating, and hybrid thermo-vibrational welding with active cooling. Among the tested conditions, the hybrid route produced the narrowest heat-affected zone, reducing its width from about 7 mm to about 3 mm, which is consistent with a compressed thermal cycle. Microhardness in the heat-affected zone decreased from 380 to 440 HV in the preheated condition to 330–370 HV in the hybrid condition. Optical microscopy further indicated a finer and more homogeneous transformed microstructure in the hybrid case. Results indicate that simultaneous vibro-treatment and controlled cooling effectively mitigate harmful metallurgical effects typically induced by rapid cooling, enabling preheat-free fabrication of thick-walled components. The proposed hybrid approach may offer energy savings, shorter production cycles, and improved automation compatibility in field welding applications.

Förderung

  • The Ministry of Education and Science of the Russian Federation

Zitieren

APA

Fairushin, A. M., Tumanova, E. Y., Tokarev, A. S., Mulyashova, N. B., Ilalov, A. S., Kanaeva, A. R., Kazakov, A. M., & Korznikova, G. F. (2026). Hybrid Thermo-Vibrational Welding with Active Cooling for Preheat-Free Joining of Martensitic 15Kh5M Steel: Microstructural Refinement and Heat-Affected Zone Control. Metals, 16(5), 499. https://doi.org/10.3390/met16050499

Vancouver

Fairushin AM, Tumanova EY, Tokarev AS, Mulyashova NB, Ilalov AS, Kanaeva AR, et al. Hybrid Thermo-Vibrational Welding with Active Cooling for Preheat-Free Joining of Martensitic 15Kh5M Steel: Microstructural Refinement and Heat-Affected Zone Control. Metals. 2026;16(5):499. doi:10.3390/met16050499

BibTeX
@article{Fairushin2026,
  author = {Fairushin, Airat M. and Tumanova, Elena Yu. and Tokarev, Andrey S. and Mulyashova, Natalya B. and Ilalov, Azamat S. and Kanaeva, Alsu R. and Kazakov, Arseny M. and Korznikova, Galiia F.},
  title = {Hybrid Thermo-Vibrational Welding with Active Cooling for Preheat-Free Joining of Martensitic 15Kh5M Steel: Microstructural Refinement and Heat-Affected Zone Control},
  journal = {Metals},
  year = {2026},
  volume = {16},
  number = {5},
  pages = {499},
  doi = {10.3390/met16050499}
}
Kostenlos starten →