Effect of Pre-Deformation on Microstructure and Mechanical Properties of a Mg-Rich High-Cu Al-Mg-Si-Cu Alloy
Metals · 26.03.2026 · 16 (4) · 366
DOI: 10.3390/met16040366 ↗Kurz gefasst
Fachartikel in der Zeitschrift Metals, online erschienen am 26.03.2026. Verfasst von Lipeng Ding und 5 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Key Research and Development Program, National Natural Science Foundation of China https://ror.org/01h0zpd94, Undergraduate Innovation and Entrepreneurship Project of Jiangsu Province.
Abstract (Originalsprache)
The influence of pre-deformation on the microstructure and mechanical properties of a Mg-rich high-Cu Al-Mg-Si-Cu alloy was systematically investigated by hardness measurement, tensile test, and atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). With the increase in pre-deformation strain (0–10%), the hardness and strength of the alloy after PB hardening increased progressively, accompanied by a continuous reduction in tensile elongation. Notably, increasing pre-deformation strain from 2% to 10% did not bring a significant enhancement in bake hardening response, despite the gradual improvement in the strain hardening capability of the alloy. An optimal pre-deformation strain of 5% is identified, which enabled the alloy to achieve a superior and industrially feasible combination of strength and ductility, balancing practical forming demand (T4 temper) and service performance (PB state). Pre-deformation can significantly affect the morphology and atomic structure of precipitates for the alloy. Dislocations introduced by pre-deformation acted as heterogeneous nucleation sites, inducing the formation of elongated and string-like precipitates along dislocation lines. A distinct Cu segregation behavior was observed in the pre-deformed alloy with the majority of Cu atoms segregated at the precipitate/α-Al interface, which was in sharp contrast to their dominant distribution within the precipitate interior in the non-pre-deformed alloy. These findings provide new insights into deformation-assisted precipitation regulation in Mg-rich high-Cu Al-Mg-Si-Cu alloys and offer practical guidance for optimizing the strength–ductility synergy of such alloys for automotive lightweight manufacturing applications.
Förderung
- the National Key Research and Development Program
- National Natural Science Foundation of China https://ror.org/01h0zpd94
- Undergraduate Innovation and Entrepreneurship Project of Jiangsu Province
Zitieren
APA
Ding, L., Yang, Y., Zheng, Y., Yin, T., Huang, H., & Weng, Y. (2026). Effect of Pre-Deformation on Microstructure and Mechanical Properties of a Mg-Rich High-Cu Al-Mg-Si-Cu Alloy. Metals, 16(4), 366. https://doi.org/10.3390/met16040366
Vancouver
Ding L, Yang Y, Zheng Y, Yin T, Huang H, Weng Y. Effect of Pre-Deformation on Microstructure and Mechanical Properties of a Mg-Rich High-Cu Al-Mg-Si-Cu Alloy. Metals. 2026;16(4):366. doi:10.3390/met16040366
BibTeX
@article{Ding2026,
author = {Ding, Lipeng and Yang, Yuqi and Zheng, Yue and Yin, Tengqiang and Huang, Huilan and Weng, Yaoyao},
title = {Effect of Pre-Deformation on Microstructure and Mechanical Properties of a Mg-Rich High-Cu Al-Mg-Si-Cu Alloy},
journal = {Metals},
year = {2026},
volume = {16},
number = {4},
pages = {366},
doi = {10.3390/met16040366}
}
EUVIMED