Comparing Microstructure and Corrosion Performance of Laser Powder Bed Fusion 316L Stainless Steel Reinforced with Varied Ceramic Particles
Metals · 01.02.2026 · 16 (2) · 173
DOI: 10.3390/met16020173 ↗Kurz gefasst
Fachartikel in der Zeitschrift Metals, online erschienen am 01.02.2026. Verfasst von Jingyang Liang und 3 weiteren Autor:innen. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 71 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Guangdong Basic and Applied Basic Research Foundation, Guangzhou Municipal Science and Technology Project.
Abstract (Originalsprache)
To address the limitations in the corrosion resistance of 316L stainless steel, ceramic reinforcements are increasingly utilized in additive manufacturing. However, their influence on corrosion behavior varies significantly. Via laser powder bed fusion (LPBF), 316L stainless steel composites reinforced with, respectively, 1 wt.% ceramic particles (TiC, SiC, SiO2, WC, Y2O3) were fabricated, and the comparing microstructure and corrosion performance was investigated in this work. The results indicated that ceramic particle addition increased porosity (0.24% to 1.40%) due to the thermal expansion coefficient mismatch between particles and matrix and defects from incompletely melted particles. Microstructural analysis revealed that LPBF-processed 316L exhibited cellular sub-grain boundaries with distinct melt pool boundaries. Ceramic particle addition refined sub-grain boundaries to varying degrees across composites, accompanied by increased sub-grain boundary density. Interfacial reactions and thermal stresses induced crack formation in SiC/316L and SiO2/316L composites. Electrochemical testing demonstrated that Y2O3/316L exhibited the highest corrosion resistance, followed by TiC/316L and WC/316L. The corrosion resistance of the as-built L-BPF 316L matrix was inferior to that of these three composites. Conversely, SiC/316L and SiO2/316L exhibited the poorest corrosion resistance. The optimized corrosion resistance of Y2O3/316L is hypothesized to result from pronounced grain refinement and the highest sub-grain boundary density, which provided abundant nucleation sites for passive film formation. Conversely, SiC/316L and SiO2/316L showed lower corrosion resistance than the as-built L-BPF 316L matrix due to elevated defect density. Corrosion morphology analysis indicated preferential corrosion propagation along melt pool boundaries in 316L, TiC/316L, WC/316L, and Y2O3/316L. In contrast, pores and microcracks in SiC/316L and SiO2/316L accelerated pit nucleation, indicating failure dominated by localized corrosion mechanisms.
Förderung
- National Natural Science Foundation of China
- Guangdong Basic and Applied Basic Research Foundation
- Guangzhou Municipal Science and Technology Project
- Young Talent Support Project of Guangzhou Association for Science and Technology
Zitieren
APA
Liang, J., Yan, J., Li, C., & Yang, Y. (2026). Comparing Microstructure and Corrosion Performance of Laser Powder Bed Fusion 316L Stainless Steel Reinforced with Varied Ceramic Particles. Metals, 16(2), 173. https://doi.org/10.3390/met16020173
Vancouver
Liang J, Yan J, Li C, Yang Y. Comparing Microstructure and Corrosion Performance of Laser Powder Bed Fusion 316L Stainless Steel Reinforced with Varied Ceramic Particles. Metals. 2026;16(2):173. doi:10.3390/met16020173
BibTeX
@article{Liang2026,
author = {Liang, Jingyang and Yan, Jin and Li, Chuanqiang and Yang, Yang},
title = {Comparing Microstructure and Corrosion Performance of Laser Powder Bed Fusion 316L Stainless Steel Reinforced with Varied Ceramic Particles},
journal = {Metals},
year = {2026},
volume = {16},
number = {2},
pages = {173},
doi = {10.3390/met16020173}
}
EUVIMED