EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Numerical Simulation of Flow and Argon Bubble Distribution in a Continuous Casting Slab Mold under Different Argon Injection Modes

Zexian He, Qiao Cheng, Haibiao Lu, Yunbo Zhong, Changgui Cheng, Jingxin Song, Zuosheng Lei

Metals · 14.12.2023 · 13 (12) · 2010

DOI: 10.3390/met13122010 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 14.12.2023. Verfasst von Zexian He und 6 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science Foundation of China, fellowship of China Postdoctoral Science Foundation, Independent Research Project of the State Key Laboratory of Advanced Special Steel, Shanghai University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A three-dimensional model is established to investigate the effect of argon injection mode, argon flow rate and casting speed on the gas–liquid two-phase flow behavior inside a slab continuous casting mold. The Eulerian–Eulerian model is employed to simulate the gas–liquid flow, and the population balance model is applied to describe the bubble breakage and coalescence process in the mold. The numerical simulation results of the bubble size distribution are verified using the water model experiment. The results show that the flow field and bubble distribution are similar between the argon injection at the upper submerged entry nozzle (SEN) and tundish upper nozzle (TUN), while the number density is larger for the argon injection of TUN. The coalescence rate of bubbles and the bubble size inside the mold increase with increasing argon flow rate. When the argon flow rate exceeds 4 L/min, the flow pattern of liquid steel changes from double-roll flow to complex flow, with aggravation of the level fluctuation of the top surface near the SEN. When the casting speed increases, the bubble breakup rate increases and results in a decrease in the size of bubbles inside the mold. At a high casting speed, the flow pattern tends to form double-roll flow, and the liquid level at the narrow face of the top surface increases.

Förderung

  • National Science Foundation of China
  • fellowship of China Postdoctoral Science Foundation
  • Independent Research Project of the State Key Laboratory of Advanced Special Steel, Shanghai University
  • Science and Technology Commission of Shanghai Municipality
  • Shanghai Technical Service Center of Science and Engineering Computing, Shanghai University

Zitieren

APA

He, Z., Cheng, Q., Lu, H., Zhong, Y., Cheng, C., Song, J., & Lei, Z. (2023). Numerical Simulation of Flow and Argon Bubble Distribution in a Continuous Casting Slab Mold under Different Argon Injection Modes. Metals, 13(12), 2010. https://doi.org/10.3390/met13122010

Vancouver

He Z, Cheng Q, Lu H, Zhong Y, Cheng C, Song J, et al. Numerical Simulation of Flow and Argon Bubble Distribution in a Continuous Casting Slab Mold under Different Argon Injection Modes. Metals. 2023;13(12):2010. doi:10.3390/met13122010

BibTeX
@article{He2023,
  author = {He, Zexian and Cheng, Qiao and Lu, Haibiao and Zhong, Yunbo and Cheng, Changgui and Song, Jingxin and Lei, Zuosheng},
  title = {Numerical Simulation of Flow and Argon Bubble Distribution in a Continuous Casting Slab Mold under Different Argon Injection Modes},
  journal = {Metals},
  year = {2023},
  volume = {13},
  number = {12},
  pages = {2010},
  doi = {10.3390/met13122010}
}
Kostenlos starten →