EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhancing the Strength and Toughness of A356.2-0.15Fe Aluminum Alloy by Trace Mn and Mg Co-Addition

Jie Cui, Jiayan Chen, Yongbo Li, Tianjiao Luo

Metals · 12.08.2023 · 13 (8) · 1451

DOI: 10.3390/met13081451 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 12.08.2023. Verfasst von Jie Cui und 3 weiteren Autor:innen. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science and Technology Program of Dezhou, Scientific Research Allowance of Dezhou University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present work, microalloying is put forward to improve the microstructure and tensile properties of A356.2-0.15Fe (wt.%) alloy by the co-addition of trace Mn and Mg. A suitable Mn/Fe mass ratio of 0.5 is obtained for alloys with 0.15Fe. The yield strength, ultimate tensile strength, and elongation of the A356.2-0.15Fe alloy with an Mn/Fe ratio of 0.5 and containing 0.42 wt.% Mg is 179 MPa, 286 MPa, and 9.1%, respectively, which is acceptable for automotive wheel hub applications. Optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and electron-probe microanalyzer (EPMA) methods are used to characterize the microstructure of the alloys. The results indicate that Mn addition promotes the transformation of the acicular β-Al5FeSi phase to the block-shaped α-Al(Fe, Mn)Si phase. The ratio of length/width of the Fe-rich phase in the alloy is reduced by 78.8% with an Mn/Fe ratio of 0.5 and containing 0.35 wt.% Mg, compared with that of the alloy without Mn addition and containing 0.35 wt.% Mg. The addition of Mg reduces the secondary dendrite arm spacing (SDAS) from 26.1 μm to 20.9 μm. The volume fraction of the precipitated Mg2Si phase in the alloy containing 0.42 wt.% Mg increases by 60% compared with that in the alloy containing 0.35 wt.% Mg. The morphology transformation of the Fe-rich phase, the reduction of SDAS, and the increase in volume fraction of precipitated Mg2Si phase comprehensively contribute to the improvement of A356.2-0.15Fe alloy. The microstructure evolution mechanism and the effect of microstructure on tensile properties are analyzed and discussed.

Förderung

  • Science and Technology Program of Dezhou
  • Scientific Research Allowance of Dezhou University

Zitieren

APA

Cui, J., Chen, J., Li, Y., & Luo, T. (2023). Enhancing the Strength and Toughness of A356.2-0.15Fe Aluminum Alloy by Trace Mn and Mg Co-Addition. Metals, 13(8), 1451. https://doi.org/10.3390/met13081451

Vancouver

Cui J, Chen J, Li Y, Luo T. Enhancing the Strength and Toughness of A356.2-0.15Fe Aluminum Alloy by Trace Mn and Mg Co-Addition. Metals. 2023;13(8):1451. doi:10.3390/met13081451

BibTeX
@article{Cui2023,
  author = {Cui, Jie and Chen, Jiayan and Li, Yongbo and Luo, Tianjiao},
  title = {Enhancing the Strength and Toughness of A356.2-0.15Fe Aluminum Alloy by Trace Mn and Mg Co-Addition},
  journal = {Metals},
  year = {2023},
  volume = {13},
  number = {8},
  pages = {1451},
  doi = {10.3390/met13081451}
}
Kostenlos starten →