EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Structure Evolution and Mechanical Properties of Sheet Al–2Cu–1.5Mn–1Mg–1Zn (wt.%) Alloy Designed for Al20Cu2Mn3 Disperoids

Nikolay Belov, Torgom Akopyan, Kirill Tsydenov, Nikolay Letyagin, Anastasya Fortuna

Metals · 11.08.2023 · 13 (8) · 1442

DOI: 10.3390/met13081442 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 11.08.2023. Verfasst von Nikolay Belov und 4 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation, Moscow Polytechnic University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work was focused on studying the possibility of increasing the strength of non-heat-treatable sheet alloy Al2Cu1.5Mn (wt.%) by the joint addition of 1% Mg and 1% Zn. The effect of these elements on the structure and mechanical properties of the new sheet Al2Cu1.5Mn alloy designed for Al20Cu2Mn3 dispersoids has been studied by calculations and experimental methods. The obtained data on the phase composition, microstructure, and physical and mechanical properties of the new alloy for different processing routes (including hot rolling, cold rolling, and annealing) have been compared with those for the ternary Mg- and Zn-free alloy. It has been shown that the formation of nanosized Al20Cu2Mn3 dispersoids (~7 vol.%) provides for the preservation of the non-recrystallized grain structure after annealing at up to 400 °C (3 h), while Mg and Zn have a positive effect on the strength due to the formation of alloyed aluminum solid solution. As a result, cold-rolled sheets of the Al2Cu1.5Mn1Mg1Zn model alloy showed a substantially higher strength performance after annealing at 400 °C in comparison with the ternary reference alloy. In particular, the UTS is ~360 vs. ~300 MPa, and the YS is 280 vs. 230 MPa. For the example of the Al2Cu1.5Mn1Mg1Zn model alloy, it has been shown that the system is promising for designing new heat-resistant alloys as a sustainable alternative to the 2xxx alloys. The new alloy has an advantage over the commercial alloys (particularly, 2219, 2024, 2014), not only in manufacturability but also in thermal stability. The sheet production cycle for the model alloy is much shorter because the stages of homogenization, solution treatment, and water quenching are excluded.

Förderung

  • Russian Science Foundation
  • Moscow Polytechnic University

Zitieren

APA

Belov, N., Akopyan, T., Tsydenov, K., Letyagin, N., & Fortuna, A. (2023). Structure Evolution and Mechanical Properties of Sheet Al–2Cu–1.5Mn–1Mg–1Zn (wt.%) Alloy Designed for Al20Cu2Mn3 Disperoids. Metals, 13(8), 1442. https://doi.org/10.3390/met13081442

Vancouver

Belov N, Akopyan T, Tsydenov K, Letyagin N, Fortuna A. Structure Evolution and Mechanical Properties of Sheet Al–2Cu–1.5Mn–1Mg–1Zn (wt.%) Alloy Designed for Al20Cu2Mn3 Disperoids. Metals. 2023;13(8):1442. doi:10.3390/met13081442

BibTeX
@article{Belov2023,
  author = {Belov, Nikolay and Akopyan, Torgom and Tsydenov, Kirill and Letyagin, Nikolay and Fortuna, Anastasya},
  title = {Structure Evolution and Mechanical Properties of Sheet Al–2Cu–1.5Mn–1Mg–1Zn (wt.%) Alloy Designed for Al20Cu2Mn3 Disperoids},
  journal = {Metals},
  year = {2023},
  volume = {13},
  number = {8},
  pages = {1442},
  doi = {10.3390/met13081442}
}
Kostenlos starten →