Comparison of Different Polymeric Membranes in Direct Contact Membrane Distillation and Air Gap Membrane Distillation Configurations
Membranes · 13.03.2025 · 15 (3) · 91
DOI: 10.3390/membranes15030091 ↗Kurz gefasst
Fachartikel in der Zeitschrift Membranes, online erschienen am 13.03.2025. Verfasst von Cristiane Raquel Sousa Mesquita und 3 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Nano & Microfluidics and Microsystems-LabMEMS, Mechanical Engineering Department, POLI & COPPE/UFRJ, Federal University of Rio de Janei…. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 108 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Agency of Petroleum, Natural Gas and Biofuels, CAPES PROCAD-Defesa, Petrogal in partnership with ANP (Project N. 23061—Research and development of microchannel-based heat sinkers for high concentration photovoltaic cells with r….
Abstract (Originalsprache)
Membrane distillation (MD) is an evolving thermal separation technique most frequently aimed at water desalination, compatible with low-grade heat sources such as waste heat from thermal engines, solar collectors, and high-concentration photovoltaic panels. This study presents a comprehensive theoretical–experimental evaluation of three commercial membranes of different materials (PE, PVDF, and PTFE), tested for two distinct MD modules—a Direct Contact Membrane Distillation (DCMD) module and an Air Gap Membrane Distillation (AGMD) module—analyzing the impact of key operational parameters on the performance of the individual membranes in each configuration. The results showed that increasing the feed saline concentration from 7 g/L to 70 g/L led to distillate flux reductions of 12.2% in the DCMD module and 42.9% in the AGMD one, averaged over the whole set of experiments. The increase in feed temperature from 65 °C to 85 °C resulted in distillate fluxes up to 2.36 times higher in the DCMD module and 2.70 times higher in the AGMD one. The PE-made membrane demonstrated the highest distillate fluxes, while the PVDF and PTFE membranes exhibited superior performance under high-salinity conditions in the AGMD module. Membranes with high contact angles, such as PTFE with 143.4°, performed better under high salinity conditions. Variations in operational parameters, such as flow rate and temperature, markedly affect the temperature and concentration polarization effects. The analyses underscored the necessity of a careful selection of membrane type for each distillation configuration by the specific characteristics of the process and its operational conditions. In addition to experimental findings, the proposed heat and mass transfer-reduced model showed good agreement with experimental data, with deviations within ±15%, effectively capturing the influence of operational parameters. Theoretical predictions showed good agreement with experimental data, confirming the model’s validity, which can be applied to optimization methodologies to improve the membrane distillation process.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Laboratory of Nano & Microfluidics and Microsystems-LabMEMS, Mechanical Engineering Department, POLI & COPPE/UFRJ, Federal University of Rio de Janeiro, 360 Av. Moniz de Aragão, CT-2-Cidade Universitária, Rio de Janeiro…
- Laboratory of Sustainable Energies Technologies, LATES-GTM, Navy Research Institute, IPqM/CTMRJ, General Directorate of Nuclear and Technological Development, DGDNTM, Brazilian Navy, 02 R. Ipiru-Cacuia, Rio de Janeiro 2…
ORCID-Profile: Cristiane Raquel Sousa Mesquita, Renato Machado Cotta
Förderung
- National Agency of Petroleum, Natural Gas and Biofuels
- CAPES PROCAD-Defesa
- Petrogal in partnership with ANP (Project N. 23061—Research and development of microchannel-based heat sinkers for high concentration photovoltaic cells with r…
- FAPERJ
- CAPES
- Brazilian Navy
Zitieren
APA
Mesquita, C. R. S., Gómez, A. O. C., Cotta, C. P. N., & Cotta, R. M. (2025). Comparison of Different Polymeric Membranes in Direct Contact Membrane Distillation and Air Gap Membrane Distillation Configurations. Membranes, 15(3), 91. https://doi.org/10.3390/membranes15030091
Vancouver
Mesquita CRS, Gómez AOC, Cotta CPN, Cotta RM. Comparison of Different Polymeric Membranes in Direct Contact Membrane Distillation and Air Gap Membrane Distillation Configurations. Membranes. 2025;15(3):91. doi:10.3390/membranes15030091
BibTeX
@article{Mesquita2025,
author = {Mesquita, Cristiane Raquel Sousa and Gómez, Abdul Orlando Cárdenas and Cotta, Carolina Palma Naveira and Cotta, Renato Machado},
title = {Comparison of Different Polymeric Membranes in Direct Contact Membrane Distillation and Air Gap Membrane Distillation Configurations},
journal = {Membranes},
year = {2025},
volume = {15},
number = {3},
pages = {91},
doi = {10.3390/membranes15030091}
}
EUVIMED