EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Simulation Study on Impact Load of an Industrial-Scale SAG Mill Based on the Discrete Element Method

Jiayi Zhao, Lun Li, Hanqi Wu, Yunfeng He, Xiaohai Ji, Yujun Xue

Machines · 14.11.2026 · 14 (11) · 1346

DOI: 10.3390/machines14111346 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Machines, online erschienen am 14.11.2026. Verfasst von Jiayi Zhao und 5 weiteren Autor:innen. Die Arbeit nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Henan Provincial Major Science and Technology Special Project Research and Industrialization of Key Technologies for Ultra-Large Green Intelligent Mineral Grin….

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study develops a comprehensive discrete element method (DEM) model of an industrial Φ5.5 m × 2.25 m semi-autogenous grinding (SAG) mill. The Hertz–Mindlin no-slip contact model is employed to simulate the complete operational process across varying critical speed fractions. By integrating the Fast Fourier Transform (FFT), load evolution is analyzed in both time and frequency domains, thereby revealing the correlation mechanism between charge motion patterns and the total shell–liner contact-force spectrum. Oil-film pressure measurements of the sliding shoe bearings provide indirect partial validation only for the simulated steady-state average load. Owing to the low 30 s sampling interval of field monitoring, transient impact peaks and frequency-domain characteristics are purely DEM-simulation outputs without experimental validation. The results indicate that the characteristics of impact load are determined by the charge motion mode: cascading corresponds to high frequency and low amplitude, while cataracting corresponds to low frequency and high amplitude. During steady operation, the load amplitude increases nonlinearly with rotational speed. Notably, in this single DEM realization, the FFT spectral amplitude of the vertical load at the dominant frequency increases by 78.1% when the critical speed fraction rises from 75% to 80%. During deceleration, the impact superposition effect is most pronounced at 75% critical speed fraction, where the FFT spectral amplitude of the vertical (FZ) load is 57.9% higher than that at the 80% critical speed (extracted from a single non-detrended short window). The relative error between experimental measurements (at 77% critical speed) and simulation results (at 80% critical speed) is 7.7%, although a 20–25% discrepancy in the estimated in-mill charge mass indicates that this agreement serves primarily as a consistency check for the mean load rather than a rigorous validation. The established load spectrum provides fundamental reference data for the dynamic load analysis of sliding shoe bearings.

Förderung

  • Henan Provincial Major Science and Technology Special Project Research and Industrialization of Key Technologies for Ultra-Large Green Intelligent Mineral Grin…

Zitieren

APA

Zhao, J., Li, L., Wu, H., He, Y., Ji, X., & Xue, Y. (2026). Simulation Study on Impact Load of an Industrial-Scale SAG Mill Based on the Discrete Element Method. Machines, 14(11), 1346. https://doi.org/10.3390/machines14111346

Vancouver

Zhao J, Li L, Wu H, He Y, Ji X, Xue Y. Simulation Study on Impact Load of an Industrial-Scale SAG Mill Based on the Discrete Element Method. Machines. 2026;14(11):1346. doi:10.3390/machines14111346

BibTeX
@article{Zhao2026,
  author = {Zhao, Jiayi and Li, Lun and Wu, Hanqi and He, Yunfeng and Ji, Xiaohai and Xue, Yujun},
  title = {Simulation Study on Impact Load of an Industrial-Scale SAG Mill Based on the Discrete Element Method},
  journal = {Machines},
  year = {2026},
  volume = {14},
  number = {11},
  pages = {1346},
  doi = {10.3390/machines14111346}
}
Kostenlos starten →