EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of Hybrid SMC–Laminated Magnetic Core Structures in Tubular Flux-Switching Permanent Magnet Linear Machines

Seung-Ahn Chae, Dae-Yong Um, Gwan-Soo Park

Machines · 30.03.2026 · 14 (4) · 381

DOI: 10.3390/machines14040381 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Machines, online erschienen am 30.03.2026. Verfasst von Seung-Ahn Chae und 2 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: New Faculty Research Grant from Gyeongsang National University, Creative Human Resource Education and Research Programs for ICT Convergence in the 4th Industrial Revolution.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Tubular flux-switching permanent-magnet linear machines (TFSPMLMs) are difficult to optimize using a single core material because conventional axial laminations suffer from severe in-plane eddy-current loss, whereas soft magnetic composites (SMCs) exhibit lower permeability and higher hysteresis loss. To address this trade-off, three hybrid SMC–laminated steel core configurations were investigated: H1, with radially laminated steel in the yoke; H2, with axially laminated steel in the tooth; and H3, with circumferential laminated steel segments. A reference SMC model (R1) and the three hybrid models were comparatively evaluated using three-dimensional finite element analysis (3D FEA). H1 and H2 showed degraded performance due to an interfacial micro-gap along the main flux path and additional in-plane eddy currents in the laminated steel regions. To mitigate these limitations, circumferential segmentation was applied to the laminated steel parts. With eight segments, H2 achieved a thrust force of 278.8 N, comparable to that of R1, while reducing iron loss by 22.5%; even a two-segment structure provided noticeable improvement. Among the investigated models, H3 showed the best overall performance by avoiding a micro-gap on the main flux path, achieving 285.5 N, and 3.9% higher thrust force and 18% lower iron loss than R1. These results indicate that H3 is the most effective hybrid-core configuration for maximizing both thrust force and loss reduction, whereas segmented H2 is an attractive practical option when manufacturability and low-loss operation are considered.

Förderung

  • New Faculty Research Grant from Gyeongsang National University
  • Creative Human Resource Education and Research Programs for ICT Convergence in the 4th Industrial Revolution

Zitieren

APA

Chae, S., Um, D., & Park, G. (2026). Investigation of Hybrid SMC–Laminated Magnetic Core Structures in Tubular Flux-Switching Permanent Magnet Linear Machines. Machines, 14(4), 381. https://doi.org/10.3390/machines14040381

Vancouver

Chae S, Um D, Park G. Investigation of Hybrid SMC–Laminated Magnetic Core Structures in Tubular Flux-Switching Permanent Magnet Linear Machines. Machines. 2026;14(4):381. doi:10.3390/machines14040381

BibTeX
@article{Chae2026,
  author = {Chae, Seung-Ahn and Um, Dae-Yong and Park, Gwan-Soo},
  title = {Investigation of Hybrid SMC–Laminated Magnetic Core Structures in Tubular Flux-Switching Permanent Magnet Linear Machines},
  journal = {Machines},
  year = {2026},
  volume = {14},
  number = {4},
  pages = {381},
  doi = {10.3390/machines14040381}
}
Kostenlos starten →