Service Life and Failure Analysis of Nylon, Polycarbonate, and IGUS i180 Polymer Gears Made by Additive Manufacturing
Machines · 25.12.2024 · 13 (1) · 5
DOI: 10.3390/machines13010005 ↗Kurz gefasst
Fachartikel in der Zeitschrift Machines, online erschienen am 25.12.2024. Verfasst von Adis J. Muminović und 9 weiteren Autor:innen. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry for Science, Higher Education, and Youth of Canton Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina.
Abstract (Originalsprache)
An assessment of different materials for additive manufacturing (AM) of polymer gears is presented in this research. Experimental testing is carried out for three different materials. Two materials are selected as the most common materials used for gears made by additive manufacturing. These materials are nylon and polycarbonate (PC). The third material is IGUS i180, which is a tribological material specially developed for additive manufacturing of parts with demands for high resistance properties such as resistance to friction, wear, and high temperatures which are essential for the long service life of gears. Gears are experimentally tested to determine service life in the form of operating cycles until failure. In addition, the gear temperature is monitored during the experimental testing. Using the value of maximum temperature at the moment of total gear failure at a specific load level enables the categorization of failure type. Different types of gear failures are categorized and presented. Taking into consideration failure type and the service life in the form of operating cycles, the applicability of analyzed materials for specific applications concerning load, speed, and thermal conditions is presented and discussed at the end of the paper. The main goal of this research was to test IGUS i180 material and compare its mechanical and thermal properties with other commonly used materials for gears manufactured by AM, such as nylon (PA6/66) and polycarbonate (PC). IGUS i180 material showed inferior properties concerning gear design in the case of high loads. This research showed that PA6/66 material is still the best solution for polymer gears production using AM, but the applicability of this material, due to temperature constraints, is still quite limited.
Förderung
- Ministry for Science, Higher Education, and Youth of Canton Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina
Zitieren
APA
Muminović, A. J., Bektašević, S., Muratović, E., Pervan, N., Smajić, J., Muminović, A., Šarić, I., Mešić, E., Trobradović, M., & Delić, M. (2024). Service Life and Failure Analysis of Nylon, Polycarbonate, and IGUS i180 Polymer Gears Made by Additive Manufacturing. Machines, 13(1), 5. https://doi.org/10.3390/machines13010005
Vancouver
Muminović AJ, Bektašević S, Muratović E, Pervan N, Smajić J, Muminović A, et al. Service Life and Failure Analysis of Nylon, Polycarbonate, and IGUS i180 Polymer Gears Made by Additive Manufacturing. Machines. 2024;13(1):5. doi:10.3390/machines13010005
BibTeX
@article{Muminovi2024,
author = {Muminović, Adis J. and Bektašević, Sunita and Muratović, Enis and Pervan, Nedim and Smajić, Jasmin and Muminović, Adil and Šarić, Isad and Mešić, Elmedin and Trobradović, Mirsad and Delić, Muamer},
title = {Service Life and Failure Analysis of Nylon, Polycarbonate, and IGUS i180 Polymer Gears Made by Additive Manufacturing},
journal = {Machines},
year = {2024},
volume = {13},
number = {1},
pages = {5},
doi = {10.3390/machines13010005}
}
EUVIMED