EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Salt-Coated High-Temperature Corrosion of Vacuum-Brazed 316L Joints

Xiaoya Wang, Chengcheng Shuai, Minxing Liao, Xuesong Leng, Linlin Song, Jun Liu, Jun Mei, Lin Zhao, Lei Zhao, Jianchao He

Materials · 18.11.2026 · 19 (22) · 4882

DOI: 10.3390/ma19224882 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.11.2026. Verfasst von Xiaoya Wang und 9 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Guangdong Foundation for Basic and Applied Research, National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the salt-coated high-temperature corrosion behavior and post-corrosion mechanical properties of 316L stainless-steel joints vacuum-brazed with three typical nickel-based filler metals: Ni-Cr-B, Ni-Cr-B-Si and Ni-Cr-Si. Salt-coated corrosion tests were conducted at 850 °C in air with NaCl deposition for up to eight cycles. In B-containing joints, CrB precipitates formed in the diffusion-affected zone, and corrosion propagated inward along their distribution paths. In the Ni-Cr-Si joint, selective oxidation of the continuously distributed Ni₃Si phase induced volume expansion and cracking, accelerating localized corrosion. This continuous Ni₃Si network was suppressed in the Ni-Cr-B-Si joint, as B preferentially reacts with Cr to form boride precipitates, which alters the solidification path and solute segregation behavior and reduces the continuity of Si-rich intermetallic phases at the seam center. The corrosion resistance follows the order Ni-Cr-B > Ni-Cr-B-Si > Ni-Cr-Si. After eight cycles, the Ni-Cr-Si joint reaches a relative corrosion depth of approximately 145 μm, approximately 32% higher than that of the Ni-Cr-B joint. The Ni-Cr-B joint retains the highest post-corrosion tensile strength (339 MPa, 38% decrease from the as-brazed state), while the Ni-Cr-Si joint suffers the most severe degradation (130 MPa, 78% decrease). These findings provide a reference for filler metal selection in high-temperature chloride-laden service environments.

Förderung

  • Guangdong Foundation for Basic and Applied Research
  • National Natural Science Foundation of China

Zitieren

APA

Wang, X., Shuai, C., Liao, M., Leng, X., Song, L., Liu, J., Mei, J., Zhao, L., Zhao, L., & He, J. (2026). Salt-Coated High-Temperature Corrosion of Vacuum-Brazed 316L Joints. Materials, 19(22), 4882. https://doi.org/10.3390/ma19224882

Vancouver

Wang X, Shuai C, Liao M, Leng X, Song L, Liu J, et al. Salt-Coated High-Temperature Corrosion of Vacuum-Brazed 316L Joints. Materials. 2026;19(22):4882. doi:10.3390/ma19224882

BibTeX
@article{Wang2026,
  author = {Wang, Xiaoya and Shuai, Chengcheng and Liao, Minxing and Leng, Xuesong and Song, Linlin and Liu, Jun and Mei, Jun and Zhao, Lin and Zhao, Lei and He, Jianchao},
  title = {Salt-Coated High-Temperature Corrosion of Vacuum-Brazed 316L Joints},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {22},
  pages = {4882},
  doi = {10.3390/ma19224882}
}
Kostenlos starten →