Structure–Property Tailoring of Long-Chain PDMS-Based Polyurethanes for Flexible MXene Strain Sensors
Materials · 17.11.2026 · 19 (22) · 4861
DOI: 10.3390/ma19224861 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 17.11.2026. Verfasst von Marija V. Pergal und 8 weiteren Autor:innen. Die Arbeit nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Fund of the Republic of Serbia, Ministry of Science, Technological Development, and Innovation.
Abstract (Originalsprache)
Flexible and mechanically adaptable polymer substrates are critical for conformable wearable sensors capable of accurately tracking human motion and vital parameters. Here, crosslinked polyurethanes (PUs) were synthesized from a long-chain poly(ethylene oxide)-b-poly(dimethylsiloxane)-b-poly(ethylene oxide) (PEO–PDMS–PEO) macrodiol (Mn = 2400 g mol−1), 4,4′-methylenediphenyl diisocyanate, and a multifunctional hyperbranched polyester, with soft-segment contents of 15–70 wt.%. Mechanical, structural, surface, and thermal properties were evaluated by indentation methods (nanoindentation, microindentation, and microindentation creep), XRD, AFM, wettability measurements, TGA, and DSC. Increasing the soft-segment content markedly reduced stiffness; Young’s modulus decreased from 1713 MPa to 112 MPa to 80 MPa as the soft segment content was increased from 30 wt.% to 50 wt.% to 70 wt.%, respectively, while hardness decreased from 89 to 4 MPa. The predominantly amorphous networks retained good thermal stability, with degradation temperature (T(10%)) values of 249–291 °C and glass transition temperature (Tg) values of 21–25 °C. Increasing the soft-segment content also increased surface roughness (Rq: 18.3–250 nm) and water contact angle (approximately 45–90°), indicating progressive surface enrichment by the low-surface-energy PDMS-containing phase. PU-50 was selected as the finger-motion sensor substrate and coated with Ti3C2Tx MXene by spray deposition. The MXene/PU-50 sensor exhibited a gauge factor of 65.9 over 0–8% strain, response/recovery times of 138/58 ms, and a signal-to-noise ratio (SNR) of 39.5 dB, demonstrating a reversible piezoresistive response with good short-term repeatability and the feasibility of using a long-chain PDMS-based PU substrate for rapid and sensitive wearable strain sensing.
Förderung
- Science Fund of the Republic of Serbia
- Ministry of Science, Technological Development, and Innovation
Zitieren
APA
Pergal, M. V., Mladenović, I. O., Pešić, I., Bakoč, A., Džambaski, Z., Rafajilović, M. R., Micić, D., Vasiljević-Radović, D., & Spasenović, M. (2026). Structure–Property Tailoring of Long-Chain PDMS-Based Polyurethanes for Flexible MXene Strain Sensors. Materials, 19(22), 4861. https://doi.org/10.3390/ma19224861
Vancouver
Pergal MV, Mladenović IO, Pešić I, Bakoč A, Džambaski Z, Rafajilović MR, et al. Structure–Property Tailoring of Long-Chain PDMS-Based Polyurethanes for Flexible MXene Strain Sensors. Materials. 2026;19(22):4861. doi:10.3390/ma19224861
BibTeX
@article{Pergal2026,
author = {Pergal, Marija V. and Mladenović, Ivana O. and Pešić, Ivan and Bakoč, Aleksa and Džambaski, Zdravko and Rafajilović, Milena Rašljić and Micić, Darko and Vasiljević-Radović, Dana and Spasenović, Marko},
title = {Structure–Property Tailoring of Long-Chain PDMS-Based Polyurethanes for Flexible MXene Strain Sensors},
journal = {Materials},
year = {2026},
volume = {19},
number = {22},
pages = {4861},
doi = {10.3390/ma19224861}
}
EUVIMED