EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA

Lintao Cao, Jiawei Yan

Materials · 13.11.2026 · 19 (22) · 4829

DOI: 10.3390/ma19224829 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 13.11.2026. Verfasst von Lintao Cao und 1 weiteren Autor:innen. Die Arbeit nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Traditional height-limiting warning barriers address the issues of susceptibility to damage and difficulty in operation and maintenance. This paper proposes a rubber-tube-suspended height-restriction frame. Based on the LSDYNA explicit dynamics platform, a finite element model for an over-height vehicle height-restriction frame was developed to simulate collisions between over-height vehicles and the rubber-tube height-restriction frame. The model systematically analyzes the collision response patterns under full-width frontal collisions and lateral collisions with offsets of 1/2 and 1/4. The results indicate that a frontal collision consists of two concentrated contact phases: an initial high-intensity impact followed by a secondary low-intensity impact. During these phases, the maximum contact reaction force reaches 148.3 kN, providing effective tactile feedback for the driver without damaging the vehicle’s roof steel structure. The secondary impact occurs during the phase where the vehicle and the rubber tube move in the same direction, at which point the peak contact force drops to 35 kN. This energy dissipation is attributed to the combined effect of reduced relative velocity at the contact interface and the unloading of tangential slip. Energy analysis shows that impact kinetic energy is dissipated gradually through a hierarchical process: it is first converted into strain energy, and subsequently into frictional energy, rotational kinetic energy, and gravitational potential energy. Among these dissipation pathways, frictional energy at the vehicle-tube interface (approximately 3.0 × 106 N × mm) dominates in the early stage, whereas frictional energy at the tube–beam interface (approximately 3.8 × 106 N × mm) becomes the primary dissipation mechanism during the long-period oscillation stage. The maximum von Mises equivalent stress in the rubber component is 1.678 MPa, providing sufficient safety margin. Offset collisions can reduce peak contact forces by 32.6–46.5%, although local stresses increase slightly. However, under all test conditions, the maximum von Mises stress in the rubber component remains below the material’s tensile strength, thereby ensuring a sufficient safety margin. This suspended rubber-tube-type high-speed limit warning barrier provides effective contact warning under a variety of impact conditions while minimizing damage to both the vehicle and the barrier itself. The research findings provide a quantitative basis for the design of passive high-speed limit warning facilities.

Zitieren

APA

Cao, L., & Yan, J. (2026). Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA. Materials, 19(22), 4829. https://doi.org/10.3390/ma19224829

Vancouver

Cao L, Yan J. Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA. Materials. 2026;19(22):4829. doi:10.3390/ma19224829

BibTeX
@article{Cao2026,
  author = {Cao, Lintao and Yan, Jiawei},
  title = {Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {22},
  pages = {4829},
  doi = {10.3390/ma19224829}
}
Kostenlos starten →